background image

16

CARE AND CLEANING

•

After using leave the cooker to cool and then clean it so that the 

incrustations are not repeatedly heated. 

•

If the dirt is stubborn, use a specific oven cleaning product 

following the instructions on the package. 

•

Clean the outside with a sponge dampened in warm water. 

• Do not use abrasive or metal pads. 

•

Clean the oven door glass with washing up liquid. 

•

Wash the accessories in the dishwasher or by hand using an oven 

cleaner. 

Replacing the bulb 

CAUTION:

 Disconnect the oven power supply cable. 

•

To replace oven bulb 

B

, remove protective cover 

A

 by turning it 

anticlockwise. 

•

After replacing the bulb, refit protective cover 

A

N.B.:

 Only use 25W bulbs, type E-14, T 300°C, available from the After-

Sales Service.

Oven door 

The door glass can easily be removed and cleaned by unscrewing the 4 

side screws. 

Removing the oven door 

To make it easier to clean the oven, the door may be removed. 
The hinges 

A

 are fitted with two mobile U-bolts 

B

 which block the door 

when it is completely open if they are hooked on to sections 

C

 of the 

hinges. 

•

Lift the door and remove it holding the sides of the oven door 

beside the hinges. 

•

Refit the door by first sliding the hinges into their groves and, 

before closing the door, detach the two mobile U-bolts 

B

 which 

were used to hook the two hinges.

3gb66072.fm  Page 16  Tuesday, December 2, 2003  5:01 PM

Summary of Contents for AKG65901IX








Reviews: