background image

5019 318 33001

AKR 938

1.

Control panel

a.

Light ON/OFF switch.

b.

Extraction and minimum extraction speed 
ON/OFF switch.

c.

Medium extraction speed switch.

d.

Maximum extraction speed switch.

2.

Grease filter.

3.

Grease filter handle.

4.

Halogen bulbs.

5.

Telescopic flue.

6.

Steam deflector screen.

To clean the grease filter

Wash the grease filter at least once a month.

1.

Disconnect the electrical power supply.

2.

Remove the grease filters - 

Fig. 1

: pull the spring 

release handle (

f

) downwards, then remove the 

filter.

3.

After cleaning the grease filter refit in reverse 
order, making sure the entire extraction surface is 
covered.

Replacing bulbs

1.

Disconnect the electrical power supply.

2.

Use a small screwdriver or any other suitable tool 
to prise off (

m - Fig. 2

) the lamp cover (

p - Fig. 2

).

3.

Replace the burnt-out bulb.
Use 20 W max halogen bulbs only, taking care not 
to touch them with hands.

4.

Close the lighting unit (snap-close).

Carbon filter Fitting and Maintenance

Fitting the carbon filter:
1.

Disconnect the electrical power supply.

2.

Remove the grease filter (

f - Fig. 1

).

3.

Remove the screw and then the filter holder 
(

g - Fig. 3

). 

4.

Fit the carbon filter (

h - Fig. 3

) in the filter holder 

(

i - Fig. 3

).

5.

Refit the filter holder and secure it to the hood 
with the screw (

g - Fig. 3

).

6.

Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon filter can 
be washed and reactivated.
With normal hood use, the filter should be cleaned 
once a month. The best way to clean the filter is in a 
dishwasher at the highest temperature possible, using 
a normal dishwasher detergent. To avoid particles of 
food or dirt settling on the filter during washing and 
giving rise to unpleasant smells, it is advisable to wash 
the filter on its own. After washing, dry the filter in the 
oven at 100° C for 10 minutes  to reactivate it.
The filter will retain its odour-absorbing capacity for 
three years, after which it must be replaced.

FIG. 1

FIG. 2

FIG. 3

F

NL

E

P

D

GR

I

GB

PRODUCT SHEET

31833001.fm5  Page 9  Wednesday, March 28, 2001  4:28 PM

Summary of Contents for AKR 938








Reviews: