background image

 

Recirculation Mode 

Caution: Do not use plastic or rigid metal ducting. 
1.  Determine  the  length  of  the  compressed  flexible  aluminum 

ducting. Attach an adequate length of 

150mm round duct 

to the air outlet adapter. 

2.  Install the charcoal filter on. 
3.  Please note that the air will flow out from the two grids on the 

sides of the decorative chimney top.   

Electrical Connection 

*  Electrical  wiring  must  be  done  by  a  qualified  person(s)  in  accordance  with  all 
applicable  codes  and  standards. 

Turn  off  electrical  power  at  service  entrance 

before wiring

* If the supply cord is damaged, it must be replaced by the manufacturer, its service 
agent or similarly qualified persons in order to avoid a hazard. 
* Do not use the plug and an extension cord other than the ones initially supplied with 
the hood. 
* The earthing of this hood is compulsory. Do not remove ground prong of the plug. 
 

TELESCOPIC CHIMNEY COMPRISING ASSEMBLY 
Decorative Chimney Top   

Raise  the  decorative  chimney  top  2.1  up  inside  the  decorative 
chimney  bottom  2.2.  Secure  decorative  chimney  top  2.1  to  the 
chimney mounting bracket 6.1 that is well fixed on the wall with 
the two chimney bracket screws 9.b supplied from two sides. 

Decorative Chimney Bottom 

1.  Carefully slide the decorative chimney bottom 2.2 down outside the decorative 

chimney  top  2.1.  Carefully  place  the  decorative  chimney 
bottom 2.2 into the recessed area of the hood body top. 

2.  Fix  the  Decorative  Chimney  Bottom  2.2  with  the  three 

decorative  Chimney  Bottom  screws  9.c  supplied  from 
inside of hood body. 

 
 
 

Summary of Contents for AKR600IX















Reviews: