ADJUSTING MINIMUM GAS SETTING OF TAPS
To ensure that the minimum setting is correctly adjusted,
remove the knob and proceed as follows:
•
tighten the screw to reduce the height of the flame (-)
•
undo the screw to increase the height of the flame (+)
The adjustment must be performed with the tap in
minimum gas setting position (small flame)
.
•
The primary air of the burners does not need to be
adjusted.
•
Light up the burners and turn the knobs from max
position
to minimum position
to check flame
stability.
Upon completion of adjustment, reseal using sealing wax or
an equivalent material.
CARE AND MAINTENANCE
To maintain your hob in perfect conditions, clean it after every use, removing any food spills.
Before any cleaning operation, disconnect the hob from the mains and wait for it to cool down.
CLEANING THE HOB SURFACE
•
All the enamelled and glass parts should be cleaned with warm water and neutral detergent.
•
The stainless steel surface may become stained in the event of prolonged contact with hard water or aggressive
detergents. It is advisable to immediately wipe any spills (water, sauce, coffee, etc.).
Clean with warm water and neutral detergent, and then dry with a soft cloth or chamois. Remove baked-on dirt with
specific cleaners for stainless steel surfaces.
•
Do not use abrasive or corrosive products, chlorine-based cleaners or pan scourers.
•
Do not use steam cleaners.
•
Do not use flammable products.
•
Do not leave acid or alkaline substances, such as vinegar, mustard, salt, sugar or lemon juice on the hob.
If you have a IXELIUM hob, observe the following cleaning recommendations:
•
Use a soft cloth (microfibre is best) dampened with water or with everyday glass cleaning detergent.
•
Do not use paper kitchen towel, which can leave traces of paper and streaks on the hob.
CLEANING THE HOB PARTS
•
Grids, burner caps and burners can be removed to be cleaned.
•
Clean them by hand with warm water and non-abrasive detergent, removing any food residues and checking that
none of the burner openings is clogged.
•
Rinse and dry.
•
Refit burners and burner caps correctly in the respective housings.
•
When replacing the grids, make sure that the panstand area is aligned with the burner and that the burner feet are
fitted in the respective housings on the hob surface. In the case of single grids, make sure that they fit on the burner
cap protuberance.
•
Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order
to ensure correct operation. Check these items frequently, and if necessary, clean them with a damp cloth. Any
baked-on food should be removed with a toothpick or needle.
Note: to avoid damaging the electric ignition device, do not use it when the burners are not in their housing.
TROUBLESHOOTING GUIDE
The hob may not work or work incorrectly. Before calling the After-Sales Service, refer to the Troubleshooting Guide to
determine the problem.
1.
The burner fails to ignite or the flame is not even
Check that:
•
The gas or electrical supplies are not shut off and especially that the gas supply tap is open.
•
The gas cylinder (liquid gas) is not empty.
•
The burner openings are not clogged.
•
The plug end is not dirty.
•
All the burner parts have been positioned correctly.
•
There are no draughts near the hob.
2.
The burner does not stay lit
Check that:
•
When lighting the burner, the knob has been pressed for enough time to activate the protection device.
•
The burner openings are not clogged near the thermocouple.
•
The end of the safety device is not dirty.
•
The minimum gas setting is correct (see relevant paragraph).
3.
The containers are not stable
Check that:
•
The bottom of the container is perfectly flat
•
The container is centered on the burner.
•
The grids have not been exchanged or positioned incorrectly.
If after the above checks the fault persists, contact the nearest After-sales Service.
AFTER-SALES SERVICE
Before calling the After-Sales Service, make sure you can give the following information:
-
type of fault or problem;
-
exact model (written on the Product Description Sheet and Warranty);
-
service number that follows the word SERVICE on the rating plate under the hob and on the Warranty;
-
your complete address and phone number.
If any repairs are required, please contact an
authorised After-Sales Service
, as indicated in the warranty.
Note: Failure to comply with these instructions may compromise the safety and quality of the product.
Spare parts are available for 10 years.
Manufacturer:
Whirlpool Europe S.r.l.
Viale G. Borghi, 27
21025 Comerio (VA)
ITALY
