background image

17

CARE AND MAINTENANCE OF THE GLASS-
CERAMIC HOB

TROUBLESHOOTING GUIDE

Cooktop not working

When pressing the control buttons, did you 

follow the instructions in the section “Using 

the hob” in the enclosed ”Product 

Description Sheet”?

Is there perhaps a power failure?

Did you dry the hob carefully after cleaning it?

1.

If a cooking zone has been selected and an “F” 

or an “ER” appear on the display followed 

by a number, contact the After Sales 

Service and inform them.

- With the exception of the message “F03” or 

ER03” that identifies the incorrect 

cleaning of the controls area.

- To solve the problem follow the instruction 

in the ICleaning and maintenance of the 

glass-ceramic hobI paragraph.

2.

If the hob does not work following intensive 

use, the hob internal temperature is too high. 

Wait a few minutes until the hob cools down.

AFTER SALES SERVICE

Before contacting After Sales Service
1. 
Try to solve the problem (see 

“Troubleshooting Guide”).

2. Turn off the appliance and restart it to see if the 

fault is repeated.

If after the above checks the fault still occurs, 

get in touch with the nearest After Sales 

Service.
Please give: 
a short description of the fault,

the precise type and model of the appliances,

the service number (the number after the word 

“Service” on the data plate), located under the hob 

or on the Product Description Sheet. The service 

number is also indicated on the warranty booklet,

your complete address and phone number.

If any repairs are required, please contact an 

authorized After-sales Service as indicated in the 

warranty.
In the unlikely event that an operation or repair is 

carried out by an unauthorised technician, 

always request a certification of the job carried out 

and insist on the use of original spare parts.
Failure to comply with these instructions may 

compromise the safety and quality of the 

product.

Clean the cooktop, when it is cool, after each use. This will 

prevent the build-up of dirt and make cleaning easier.

Important: at all costs avoid the use of high pressure water or 

steam cleaning equipment.

Use a clean cloth, absorbent kitchen wipes and washing up 

liquid or a specific glass ceramic cleaner.

Remove baked-on dirt with the supplied scraper tool and 

specific cleaning products.

Food spills should be cleaned off before they bake onto the 

glass ceramic surface.

Foods with high sugar content (toffee, fruit juice, jam, etc.) 

that boil over while cooking, or spattered sugar stains must be 

immediately removed using a scraper.

Do not use abrasive products, bleach, oven-cleaner spray or 

pan scourers.

The cooktop should be treated periodically with a proprietary 

brand of protective wax for glass-ceramic hobs.

31902042GB.fm  Page 17  Friday, April 11, 2008  5:42 PM

Summary of Contents for AKT 833








Reviews: