Whirlpool is a registered trademark of Whirlpool USA
5019 301 15256
Add the detergent as described in the programme table and in the
chapter “Detergent and Additives” in your Instructions for Use.
1.
Press “On/Off”
to switch on the washer. The light of the selected
programme is on, and the “Start (Pause)” button
blinks.
2.
Turn the programme selector to the desired programme -
it is marked by a light.
3.
The predefined temperature and spin speed can be altered
by pressing the “Temperature”
and the “Spin speed”
modifier.
Selecting any option or modifier, the indication lights up. If the
combination of programme, options or modifiers is not possible,
the indication lights switch off automatically and a signal sounds.
“Eco” button
• The duration of the wash is extended and the temperature
reduced. This saves you energy and maintains good washing results.
“Easy ironing” button
• Reduces creasing by increased water quantity and a very gentle spin.
“Rinse hold” button
• The laundry remains in the last rinse water without being spun:
this prevents creasing and colours from changing.
• Particularly useful if you want to postpone spinning to a later
time, or if you want to drain only.
• Do not leave the laundry to soak in the rinse hold for too long.
Note: The programme starts to “Rinse hold” when the “Rinse hold”
button light blinks; the “Start (Pause)” button light
also blinks.
Terminate the “Rinse hold” option
:
• Press the “Rinse hold” or the “Start (Pause)” button
; the
programme will terminate automatically with the final spin
cycle for the present wash programme.
• If you do not wish to spin the clothes, press and hold the
“Reset (Drain)” button
for a few seconds. The water
is drained out then, before the door can be opened.
“Spin speed” modifier
• Every programme has an automatic predefined spin speed.
• Press the button to set another spin speed.
• If you select spin speed “0”, the final spinning is cancelled and
the water is drained out only at the end of the programme.
“Rinse” modifier
• “SkinCare”
: maximum amount of rinse water is added,
and rinse cycle is prolonged.
• “Intensive rinse”
: more rinse water is added, and rinse
cycle is prolonged.
• Particularly suitable for areas with very soft water, for baby
clothes or to help people with skin allergies.
“Options” modifier
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy for
cold fill
(kWh)
Energy for
hot fill**
(kWh)
Approximate programme
duration with cold fill
(hours : minutes)
Approximate programme
duration with hot fill
(hours : minutes)**
Sanitary (Antibacterial)
95
10.0
102*
3.02
1.98
2:50
2:05
Heavy duty with “Eco”
and “Heavy soil” ***
60
10.0
76
1.51
0.82
3:10
3:10
Heavy duty
60
10.0
78
1.59
0.75
2:10
2:00
Heavy duty
60
5.5
58
1.20
0.70
1:45
1:40
Heavy duty
60
3.0
44
0.90
0.65
1:30
1:25
Heavy duty
60
1.0
28
0.60
0.46
1:20
1:20
Heavy duty
40
10.0
96
1.04
0.25
2:10
1:25
Heavy duty
40
5.5
50
0.52
0.22
1:30
1:20
Heavy duty
40
3.0
40
0.50
0.20
1:15
1:10
Heavy duty
40
1.0
30
0.36
0.19
0:55
0:50
Synthetics
40
5.0
61
0.75
0.35
1:45
1:45
Synthetics
40
3.0
55
0.65
0.32
1:45
1:35
Kids wear
40
5.0
75
0.64
0.25
1:45
1:30
Daily
40
5.0
50
0.70
0.25
1:00
1:00
Express
30
5.0
40
0.35
0.09
0:30
0:30
Sport
30
4.0
52
0.47
0.17
1:30
1:30
Big items
40
4.0
80
0.60
0.34
1:20
1:20
Delicates
30
4.0
86
0.45
0.45
0:55
0:55
Wool
40
3.0
68
0.70
0.70
0:45
0:45
Handwash
30
3.0
97
0.45
0.45
0:40
0:40
Whitest whites
60
10.0
98
1.35
0.75
2:15
2:10
The remaining programme time can deviate from the values in the table as it depends on the size of your wash load, water inlet temperature etc.; the
remaining time indication is newly calculated and updated if necessary approximately 20 minutes after programme start.
The consumption data for “Heavy duty” refer to a programme setting without “Eco” and “Heavy soil”, except the data which is indicated in the line marked with “***”.
*
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
**
The grey shaded columns show energy consumptions and programme durations for the washing machine being connected to both hot and cold fill,
with a hot fill inlet temperature of 60°C. The columns left from them show energy consumptions and programme durations for the washing machine
being connected to cold water only by the Y-adapter.
***
Reference programme for Energy Label (Heavy duty 60°C with default settings).
ADD DETERGENT, CLOSE THE DOOR AND
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION OR MODIFIER
Prewash
:
• Adds a prewash cycle to the programme selected.
• Use only for heavily soiled loads (e.g. sand, granular dirt).
• Increases the cycle time by approx. 25 minutes.
• Do not use liquid detergent for the main wash when selecting
“Prewash”.
Clean +
• Choose this option if you use an in-wash additive for stain
removal (powder, for example Vanish).
• Optimizes the additive’s efficiency to get better wash
performance and stain removal.
• Select temperature of 30 or 40°C and use with maximum load.
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the prewash chamber.
• Appropriate for use of stain removers and bleaches on oxygen
basis. Chlorine or perborate bleaches must not be used!
Normal
“Soil level” modifier
• Adapts the programme duration to the soil level of your laundry.
= Normal /
= Soiled /
= Heavy soil
If there is a programme setting which you use frequently, the
washing machine offers the possibility to save one setting for each
programme so that it can be used again by just pushing one button.
• Select the desired programme, temperature, spin speed and
options/modifiers.
Press and hold the “Favourites” button
for some seconds; the
light goes on and a signal sounds when the programme setting is saved.
Next time you want to use your individual programme setting, turn the
programme selector to the desired programme, shortly push the
“Favourites” button
and start by pressing “Start (Pause)”
.
If you want to replace the saved setting by another one:
• Select the programme desired and the new temperature, spin,
options/modifier setting.
• Press and hold the “Favourites” button
for at least 3
seconds; the previously saved setting is replaced by the new one.
The “Start delay”
allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper.
• Select programme, temperature and options/modifiers as desired.
• Press the “Start delay” button to select the delay time by 1 to 24 hours;
• Press and hold the “Start (Pause)” button
; the
countdown of the delay time begins. The light of the “Start
delay” button will keep blinking until the programme starts.
• The time delay indication disappears when the programme
starts and it is replaced by the remaining time.
To cancel the “Start delay”:
• Press “Reset (Drain)”
for at least 3 seconds, or set the
delay time to “0:0” - the delay time will disappear from the
display after a few seconds.
Turn on the tap and press and hold the “Start (Pause)” button
- the button’s light stops blinking and goes on; it will take some time
until water enters into the washing machine.
The programme sequence indicator on the display shows the
sequence reached in the programme. After starting the
programme, the indication runs from left to right through “Add
garment”, prewash, wash, rinse, spin. When a programme
sequence is finished, the corresponding symbol goes off.
The display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining
time is newly calculated in certain programme phases. If this is the
case, an animation appears on the display and the and the “6
th
Sense” symbol
lights up.
As soon as a programme starts, the “Door locked” symbol
lights
up on the display.
You can interrupt the programme by pressing “Start (Pause)”
- the light blinks. The “Door locked” symbol
on the display goes
off and you can open the door. In certain programme phases, the
“Door locked” symbol
remains lit to show that the door cannot
be opened in the present programme phase, e.g. when the water
level is too high or during spinning.
As long as the “Add garment” symbol
lights up on the display,
you can add more washing: press “Start (Pause)”
, open the
door, add your washing, close the door and press “Start (Pause)”
to continue the programme.
“End” appears on the display, and a signal sounds.
1.
Switch the machine off by pressing “On/Off”
.
2.
Turn off the tap and open the door to unload your washing. Leave
the door open for some time so that the washer’s inside can dry.
1.
Press the “Start (Pause)” button
to interrupt the
programme. The light blinks.
2.
Select the new programme, temperature and options/
modifiers as desired.
3.
Press the “Start (Pause)” button
again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add detergent
for this programme.
Press and hold the “Reset (Drain)” button
for a few
seconds; the light blinks. It will take some time until any existing
water is drained out and the door can be opened (up to 10
minutes). Caution, the washing could still be hot!
SAVE YOUR FAVOURITE PROGRAMMES
START DELAY
➡
➡
➡
PROGRAMME START
ADD WASHING/DOOR LOCK
PROGRAMME END
CHANGE THE PROGRAMME, TEMPERATURE,
OPTIONS AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
IF THE WASHING MACHINE APPEARS TO BE DAMAGED, CONTACT THE MACHINE OWNER AND, IF NECESSARY, THE AFTER-SALES SERVICE.
