5019 301 05696
Whirlpool is a registered trademark of Whirlpool USA
Add the detergent as described in the programme
table or in the chapter “Detergents and Additives”
in the booklet.
1. Turn the programme selector knob to the
desired programme and temperature.
2. The remaining time display shows the duration
of the chosen programme (in hours and minutes)
and after taking some seconds for calculating, the
indication of the “Start/Pause” button is flashing.
3. The programme sequence and the predefined
spin speed indication corresponding to the
selected programme lights up.
Selecting any option the indication lights up.
When the combination of programme, additional
options and temperature is not possible, the indication
lights switch off automatically. Unsuitable
combinations of options are deselected automatically.
“Easy ironing” button
• Can be used together with “Cotton”, “Synthetics”
and “Daily load” programmes to make ironing easier.
• Increases the water quantity and the clothes are
spun very soft.
“Eco” button
• The duration of the wash is extended and the
temperature reduced to save energy but
maintaining good washing results.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. The cycle time increases
approximately 15 min.
“Intensive rinse” button
• More water and a longer time in rinse cycle is added.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programme “Synthetics”, “Daily load” and “Delicates”.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
Note: The programme stops to “Rinse hold” at
the time the “Rinse hold” light in the programme
sequence indication is on.
Terminate the “Rinse hold” option:
• Press the “Rinse hold” button again; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob counterclockwise to
the “Drain” programme and press the
“Start/Pause” button again when the indication
next to it is flashing.
“Variable spin” button
• Every programme has an automatic predefined
maximum spin speed.
DATA
Programme
Temperature
(°C)
Load
(kg)
Approx.
Programme
Duration
(hours : minutes)*
Cotton
95
7.5
2:05
Cotton
60
7.5
2:25
Cotton
40
5.0
2:10
Synthetics
60
2.5
1:35
Synthetics
40
2.5
1:25
Daily load
40
3.0
1:05
Quick wash
30
3.0
0:35
Delicates
40
1.5
0:50
Wool
40
1.0
0:45
Handwash
30
1.0
0:45
Prewash cycle might increase programme duration. Consumption data in the home may vary in relation to the water supply
pressure and temperature, the load and the type of wash.
*
The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
• Press the button to set another spin speed.
• If the spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper.
• Press the “Start delay” button to select the delay
time by 1 to 23 hours;
• Press the “Start/Pause” button.
The indication next to the “Start delay” button
lights up and goes off when the programme starts.
• The time delay indication disappears when the
programme starts and it is replaced by the
remaining time.
• The number of hours preselected can later be
reduced pressing again the “Start delay” button.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
• Turn the programme selector to the
“
Off
/0”
position.
• Reselect the desired programme and options and
press “Start/Pause” button to start the programme.
..after having pressed the “Start/Pause” button:
• Press the “Reset” button for at least 3 seconds -
the start delay time disappears from the
remaining time display, then
• either start the chosen programme by pressing
the “Start/Pause” button twice
• or turn the programme selector knob to the
“Off/0” position and choose another programme.
Open the tap and press the “Start/Pause” button.
The indication next to the “Start/Pause” button
lights up. The indications show the sequence
reached in the programme. After starting the
programme, the sequence indication runs from left
to right through Wash, Rinse, Spin.
When the sequence of the programme is finished
the corresponding indication goes out.
The appliance is not intended for use by young
children or infirm persons without supervision.
Young children should be supervised to ensure that
they do not play with the appliance.
CAUTION: If this appliance is supplied from a cord
extension set or electrical portable outlet device,
the cord extension set or portable outlet device
must be positioned so that it is not subject to
splashing or ingress of moisture.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
“Door locked”
As long as a washing programme is running, the
lamp lights up to show that the door cannot be
opened. When the indication goes off, the door can
be opened again.
“Aquasure”
Lighting up of the water stop indication can be caused
by a leak in the appliance or hose. Please refer to the
“Troubleshooting Guide” in the Instructions for Use.
•
The remaining time is on “0:00” and all the lights
of the programme sequence indication are off.
1. Turn the programme selector to the
“
Off
/0”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry out.
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
The “Reset” button cancels a programme before
the end.
•
Press the “Reset” button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
START DELAY
PROGRAMME START
SAFETY
RED INDICATIONS
PROGRAMME END
CHANGE THE PROGRAMME, OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30105696GB.fm Page 2 Wednesday, July 6, 2005 5:38 PM
Black process 45.0° 100.0 LPI
