background image

MICROWAVE HOOD COMBINATION

INSTALLATION INSTRUCTIONS

MICROWAVE HOOD COMBINATION SAFETY

This product is suitable for use above electric or gas cooking products up to 36" (91.4 cm) wide.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the 
illustration in these installation instructions.

Table of Contents

MICROWAVE HOOD COMBINATION SAFETY .............................. 1

INSTALLATION REQUIREMENTS ................................................... 2

Tools and Parts............................................................................... 2
Location Requirements................................................................... 2
Product Dimensions ....................................................................... 3
Electrical Requirements .................................................................. 3

INSTALLATION INSTRUCTIONS ..................................................... 4

Remove Mounting Plate ................................................................. 4
Convert Microwave Oven to External Venting ............................... 4
Locate Wall Stud(s) ......................................................................... 6
Mark Rear Wall................................................................................ 7
Drill Holes in Rear Wall.................................................................... 7
Attach Mounting Plate to Wall ........................................................ 8
Prepare Upper Cabinet................................................................... 8
Install the Microwave Oven ............................................................ 9
Complete Installation .................................................................... 10

VENTING DESIGN SPECIFICATIONS............................................ 11

ASSISTANCE ................................................................................... 12

Replacement Parts ....................................................................... 12
Accessories................................................................................... 12

8206589

You can be killed or seriously injured if you don't immediately 
 

You

 

can be killed or seriously injured if you don't follow 

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety 
messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Summary of Contents for  GH7208XRS













Reviews: