Whirlpool Gold WFD195 Installation Instructions Manual Download | Manualshive

Page: 40 / 48

background image

40

Diagnostic Chart

The red diagnostic LED blinks to assist in troubleshooting the uit. The number of blinks refers to a specific fault code.

Symptoms of
Abnormal
Operation

Associated
LED Code

Fault Description Possible Causes

Corrective Actions

Notes and
Cautions

■

Furnace fails to
operate.

■

Integrated
control module
diagnostic LED
display
provides no
signal.

None

■

No 115-volt
power to
furnace, or no
24-volt power to
integrated
control module.

■

Blown fuse or
circuit breaker.

■

Internal fault in
Integrated
control module.

■

Manual disconnect
switch Off, door switch
open or 24-volt wire
improperly connected or
loose.

■

Blown fuse or circuit
breaker

■

Integrated control
module has an internal
fault.

■

Assure 115-volt power
to the furnace, and
24-volt power to
integrated control
module

■

Check integrated
control module fuse.
Replace with 3A
automotive fuse, if
necessary.

■

Check for possible
shorts in 115-volt and
24-volt circuits. Repair
as necessary.

■

Replace bad
integrated control
module.

■

Turn off power
prior to repair.

■

Replace
integrated control
module fuse with
3A automotive
fuse.

■

Read precautions
in “Electrostatic
Discharge”
section of manual.

■

Replace
integrated control
module with
current
replacement
parts.

■

LED display is
steady on

Continuous

On

■

Normal
operation

■

Normal operation

■

None

■

Normal operation

■

Furnace fails to
operate.

■

Integrated
control module
diagnostic LED
is flashing
1 flash.

1 flash

■

Furnace lockout
due to an
excessive
number of
ignition “retries”
(3 total).

■

Failure to establish
flame. No gas to
burners, front cover
pressure switch stuck
open, bad igniter or
igniter alignment,
improper orifices or
coated/oxidized or
improperly connected
flame sensor.

■

Loss of flame after
establishment.
Interrupted gas supply,
lazy burner flames
(improper gas pressure
or restriction in flue and/
or combustion air
piping), front cover
pressure switch
opening, or improper
induced draft blower
performance.

■

Locate and correct gas
interruption.

■

Check front cover
pressure switch
operation (hose, wiring,
contact operation).
Correct if necessary.

■

Replace or realign
igniter. Igniter is fragile,
handle gently.

■

Check flame sense
signal. Sand sensor if
coated and/or oxidized.

■

Check flue piping for
blockage, proper
length, elbows and
termination.

■

Verify proper induced
draft blower
performance.

■

Turn off power
prior to repair.

■

Igniter is fragile,
handle with care.

■

Sand flame
sensor with
emery cloth.

■

See “Vent/Flue
Pipe” section for
piping details.

■

Furnace fails to
operate.

■

Integrated
control module
diagnostic LED
is flashing 2
flashes.

2 flashes

■

Pressure switch
circuit is closed.

■

Induced draft
blower is not
operating.

■

Induced draft blower
pressure switch
contacts sticking.

■

Shorts in pressure
switch circuit.

■

Replace induced draft
blower pressure
switch.

■

Repair short.

■

Turn off power
prior to repair.

■

Replace pressure
switch with
correct
replacement part.

HIGH VOLTAGE!

WARNING

To avoid personal injury or death due to electrical shock, disconnect electrical power
before performing any service or maintenance.

«
...
38
39
40
41
42
...
»

Summary of Contents for Gold WFD195

















































Reviews:

No comments

Related manuals for Gold WFD195

Brand: SummerAire Pages: 7

Brand: SummerAire Pages: 15

Brand: Lennox Pages: 6

Brand: Lennox Pages: 32

Brand: Daikin Pages: 82

Brand: Arcoaire Pages: 40

Brand: A-Maize-Ing Heat Pages: 87

Brand: Trane Pages: 44

Brand: Johnson Pages: 20

Brand: Johnson Pages: 40

Brand: KEER Pages: 34

Kuuma Vapor-Fire 200

Brand: Lamppa Pages: 24

Brand: Coleman Pages: 18

Brand: Amana Pages: 10

CARBOLITE GERO CWF 12/23

Brand: VERDER Pages: 36

GME80603B Series

Brand: Goodman Pages: 8

Brand: Goodman Pages: 8

Brand: Goodman Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands