Whirlpool HYBRIDCARE YWHD560CHW0 Installation Instructions Manual Download

Page: 16 / 20

COMPLETE INSTALLATION

CHECKLIST

Check that all parts are now installed. If there is an extra

part, go back through steps to see what was skipped.

Check that dryer is level. See “Level Dryer.”

Check that you have all of your tools.

Dispose of/recycle all packaging materials.

Check dryer’s final location.

Remove film on console and any tape remaining on dryer.

Wipe dryer drum interior thoroughly with a damp cloth to

remove any dust.

Read “Dryer Use” in your Use and Care Guide.

For power supply cord installation, plug into a grounded

outlet. For direct wire installation, turn on power.

Select a Timed Dry heated cycle and start dryer.

If dryer will not start, check the following:

  • Controls are set to a running or On position.
  • Start button has been pressed firmly.
  • Dryer is plugged into an outlet and/or electrical

supply.
• Household fuse is intact and tight or circuit breaker

has not tripped.
• Dryer door is closed.

This dryer automatically runs an installation diagnostic routine

at the start of its first cycle.

NOTE:

You may notice an odor when dryer is first heated.

This odor is common when heating element is first used.

The odor will go away.

#2 Phillips screwdriver

Min. 8" (203 mm) long

TORX

, T20

and T25

†

screwdrivers

Tools needed:

†

TORX, T20, and T25 are registered trademarks of Acument Intellectual Properties, LLC.

DOOR REVERSAL (OPTIONAL)

The following instructions are for models with round doors.

Disconnect wiring from door

Using a Phillips screwdriver, remove middle screw in hinge.

Disconnect wiring. Tuck wiring into opening.

DOORS WITH LCD SCREEN:

Summary of Contents for HYBRIDCARE YWHD560CHW0





















Search results

Summary of Contents for HYBRIDCARE YWHD560CHW0

Reviews:

Related manuals for HYBRIDCARE YWHD560CHW0

Brands by name

Popular brands

Whirlpool HYBRIDCARE YWHD560CHW0, Installation Instructions Manual

Search results

Summary of Contents for HYBRIDCARE YWHD560CHW0

Reviews:

Related manuals for HYBRIDCARE YWHD560CHW0

Brands by name

Popular brands