background image

 

2

 

LFP580GR 

ABNORMAL CONDITION 
 
When the washer is abnormal, the washer stops as the every

 

actions turns off, beep tone   

sounds ON-0.3 second and OFF-0.3 second for 10 seconds and course lamps blink on and off. The 
washer judges the following five conditions as abnormal condition. 
 
1)

 

Abnormal condition of drain   
In  draining,  the  water  level  does  not  go  down  below  the  reset  level  of  the  water  level  sensor 
within 8 minutes. 
 
Four of the course lamp

 (NORMAL

DELICATE

BLANKET

ECO-SPEEDY) 

begin blinking on and 

off at the same time and the electric buzzer sounds to indicate a problem. 
 

2)

 

Abnormal condition of spin-dry         
• The safety switch works 3 times continuously. 
Four of the course lamp

 (NORMAL

HEAVY DUTY

BLANKET

ECO-SPEEDY) 

begin blinking on 

and off at the same time and the electric buzzer sounds to indicate a problem. 
 
• The washer lid is opened. 

The electric buzzer sounds to indicate a problem and non-course lamp blinking on and off . 

 

3)

 

Abnormal condition of water level sensor. 
The water level sensor malfunctions. 
Four of the course lamp

 (NORMAL

HEAVY DUTY

DELICATE

BLANKET)

 begin blinking on and 

off at the same time and the electric buzzer sounds to indicate a problem. 

 
4)

 

Abnormal condition of water supply. 
In  supplying  with  water,  the  water  level  does  not  reach  1level  within  15  minutes  or  does  not 
reach your chosen water level within 30 minutes. 
 
Four of the course lamp(

HEAVY DUTY

DELICATE

BLANKET

ECO-SPEEDY) 

blinking on and 

off at the same time and the electric buzzer sounds to indicate a problem. 

 
5)

 

Abnormal condition of wash.   
Four of the course lamp

 (NORMAL

HEAVY DUTY

DELICATE

ECO-SPEEDY) 

  blinking on and 

off at the same time and the electric buzzer sounds to indicate a problem. 

 

 

 

 

 

 

 

 

 

Summary of Contents for LFP580GR













Reviews: