background image

7

2. Connect the 2 white wires (D) and the green (or bare) ground 

wire (of the range cable) using a UL listed wire connector.

3. Connect the 2 red wires (G) together using a UL listed wire 

connector.

4. Install junction box cover.

Install Range

1. Using 2 or more people, lift range partially into cabinet cutout 

using the oven opening as an area to grip. 

NOTE: Push against seal area of oven front frame when 
pushing range into cabinet. Do not push against outside 
edges.

2. Push against seal area of front frame to push range into 

cabinet until shipping feet almost contact cabinet.

3. Use a Phillips screwdriver to remove and discard shipping 

feet.

4. Push range completely into cabinet and center range in 

cabinet cutout.

5. Securely fasten range to cabinet using the two #8-14 x 1" 

screws provided. Insert the screws through holes in mounting 
rails. Do not overtighten screws.

6. Slide top end of each trim piece upward onto range side rails.

7. Push each trim piece into place at bottom of trim.

8. Use screws to attach each trim piece to range.

9. Replace oven racks.

10. Replace oven door by inserting ends of hinges into hinge 

slots in the oven frame.

11. Push hinges in as far as they will go and open the oven door. 

You should feel the oven door drop into place.

12. Rotate both hinge latches back to the locked position.

13. Check that the door is free to open and close. If it is not, 

repeat the removal and installation procedures. See “Remove 
Oven Trim” section.

14. Reconnect power.

15. Display panel will light briefly, and “PF” should appear in the 

display.

16. If display panel does not light, please reference the 

“Assistance or Service” section of the Use and Care Guide or 
contact the dealer from whom you purchased your range.

A. Shipping foot

A

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Securely attach mounting screws to cabinet.

Reattach mounting screws if the range is moved.

Failure to follow these instructions can result in death 
or serious burns to children and adults.

A. 2 screws

A. Oven trim

A

A

Summary of Contents for RS696PXGQ









Reviews: