background image

4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. 

The parts supplied are in the washer drum. 

Tools needed for connecting the water inlet hoses 

Pliers (that open to 1

9⁄16

" [39.5 mm]) 

Flashlight (optional)

Tools needed for installation

Open end wrenches 13 mm and 12 mm
Level
Wood block 
Ruler or measuring tape

Parts supplied 

Alternate Parts

Your installation may require additional parts. If you are interested 

in purchasing one of the items listed here, call the toll-free 

number on the cover or in the “Assistance or Service” section. 

Options

Pedestal

You have the option of purchasing a pedestal for this washer. You 

may select an 11.8" (30.0 cm)  pedestal. The pedestal will add to 

the total height of the washer. 

Optional pedestal 

Stack Kit

Are you planning to stack your washer and dryer? To do so you 

will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your washer 

or refer to the “Assistance or Service” section. Ask for Part 

Number W10178021.

Location Requirements

Selecting the proper location for your washer improves 

performance and minimizes noise and possible washer “walk.”

Your washer can be installed under a custom counter, or in a 

basement, laundry room, closet, or recessed area. See “Drain 

System.”

Companion appliance location requirements should also be 

considered. Proper installation is your responsibility.

You will need

A water heater set to deliver 120°F (49°C) water to the washer.
A grounded electrical outlet located within 5.4 ft (1.65 m) of 

where the power cord is attached to the back of the washer. 

See “Electrical Requirements.”
Hot and cold water faucets located within 4 ft (1.2 m) of the 

hot and cold water

ll valves, and water pressure of 

20-100 psi (137.9-689.6 kPa).
A level 

floor

 with a maximum slope of 1" (2.5 cm) under entire 

washer. Installing the washer on soft

oor surfaces, such as 

carpets or surfaces with foam backing, is not recommended.
A sturdy and solid 

oor to support the washer with a total 

weight (water and load) of 400 lbs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C). 

Some water can remain in the washer and can cause damage in 

low temperatures.

A. U-shaped hose form

B. Water inlet hoses (2)

C. Inlet hose washers (4)

D. Beaded cable tie

If You Have

You Will Need to Buy

Laundry tub or 

standpipe taller 

than 55" (1.4 m)

Sump pump system (if not already 

available)

Overhead sewer

Standard 20 gal. (76 L), 30" (76.2 cm) tall 

drain tub or utility sink and sump pump 

(available from local plumbing suppliers)

Floor drain

Siphon break, Part Number 285834; 

additional drain hose 

Part Number 8318155; and connector kit, 

Part Number 285835 

Drain hose too 

short

4 ft (1.2 m) drain hose extension kit, 

Part Number 285863

Water faucets 

beyond reach of 

ll 

hoses

2 longer water 

ll hoses: 

6 ft (1.8 m) Part Number 76314

10 ft (3.0 m) Part Number 350008

A

B

C

D

Pedestal 

Height

Approximate 

Height with

Washer

Color

Model

Number

11.8" (30.0 cm)

44.7" (113.5 cm)

White

LAB0050PQ

Summary of Contents for W10175588C

























Reviews: