background image

3

Product Dimensions

   * Range can be raised approximately 1" (2.5 cm) by adjusting 

the leveling legs.

 ** Model/serial/rating plates may be rotated up from behind the 

control panel for viewing from the front of the range.

*** Excludes handle. Dimension given is from wall to front of 

oven door and will vary based on electric outlet receptacle 

installation.

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (63.5 cm) 

countertop depth, 24" (61.0 cm) base cabinet depth, and 

36" (91.4 cm) countertop height.

IMPORTANT:

 If installing a range hood or microwave hood 

combination above the range, follow the range hood or 

microwave hood combination installation instructions for 

dimensional clearances above the cooktop surface.
A freestanding range may be installed next to combustible walls 

with zero clearance.

Proper positioning of outlet shown above.
 * Nothing located in shaded areas can extend more than 

1

1

/

2

" (3.8 cm) from wall or range will not slide all the way back.

NOTE:

 24" (61.0 cm) minimum when bottom of wood or metal 

cabinet is covered by not less than 

1

/

4

" (0.64 cm) flame-retardant 

millboard covered with not less than No. 28 MSG sheet steel, 

0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum, or 

0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the 

cooking platform and the bottom of an uncovered wood or metal 

cabinet.

A. 35

3

/

4

" ± 

1

/

8

" (90.8 cm ± 

0.3 cm) cooktop height 

(minimum) with leveling legs 

screwed all the way in*

B.  Model/serial/rating plates 

(located behind the control 

panel)**

C. 47

1

/

8

" ± 

1

/

8

" (119.7 cm 

± 0.3 cm) overall height 

(minimum) with leveling legs 

screwed all the way in*

D. 28

1

/

2

" ± 

1

/

4

" (72.4 cm ± 

0.6 cm) depth with handle

E. 26

1

/

8

" ± 

1

/

8

" (66.4 cm ± 

0.3 cm)***

F. 29

15

/

16

" ± 

1

/

16

" (76.0 cm ± 

0.2 cm) width

B**

A*

F

E***

D

C*

A

B

C

D

E

F

G

H

I

J

K

A.  18" (45.7 cm) upper 

cabinet to countertop

B.  13" (33.0 cm) upper 

cabinet depth

C.  30" (76.2 cm) min. 

opening width

D.  For minimum clearance 

to the top of the cooktop, 

see NOTE.

E.  U.S.A.: 30" (76.2 cm) min. 

opening width  

Canada: 31" (78.7 cm) 

min. opening width

F.  Cabinet door or hinge 

should not extend into 

cutout*

G. 1

1

/

2

" (3.8 cm) min. from 

right side cabinet

H.  2" (5.1 cm) min. from floor
I.  7" (17.8 cm) height
J.  8" (20.3 cm) width
K. 3

1

/

2

" (8.9 cm) min. from 

floor

Summary of Contents for W10430958A





















Reviews: