29
ELECTRONIC CONTROL SETUP INSTRUCTIONS
How to Use the Buttons to Program the Controls
1.
The COTTON/WHITES button is used to adjust the values
associated with set-up codes. Pressing the button will
change the value by increments. Rapid adjustment is
possible by holding down the button.
2.
The PERM PRESS button will advance through the set-up
codes. Pressing this button will advance to the next available
set-up code. Holding down the button will automatically
advance through the set-up codes at a rate faster than
1 per second.
3.
The COLORS/DELICATES button is used to select
or deselect options.
Start Operating Setup
Insert service access door key, turn, and lift to remove service
access door.
Dryers with Card Reader Installed:
Once the debit card reader is installed (according to the
reader manufacturer’s instructions), the set-up mode can be
entered by inserting a manual set-up card (supplied by the
reader manufacturer) into the card slot. If manual set-up card
is not available, only the diagnostic mode can be entered by
removing the service access door.
IMPORTANT:
To access set-up mode or diagnostic mode,
use a service key (9050 models) to open the service access
door. If a card reader is installed, a service card is available
for accessing diagnostics. If a service key is not available
(9060 models), the AA1 connector must be removed or
the Service Access Code described below must be used.
The console must not be opened unless power is first
disconnected from the dryer. To access connector AA1:
1.
Unplug dryer or disconnect power.
2.
Open console, remove plug on AA1, and close console.
3.
Plug in dryer or reconnect power.
The dryer is now in the set-up mode.
To enter the alternative Service Access Code and enter set-up
mode: Press the Left Button, Right Button, Left Button, Right
Button, and Right Button.
NOTE:
It is not necessary to set up the dryer with the following
codes; the dryer is pre-set at the factory. These codes can be
used to change settings, if desired.
Set-Up Codes
Q
The PERM PRESS button will advance from code to code.
Q
The COTTON/WHITES button will change the code value.
Q
The COLORS/DELICATES button will select or deselect
options.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.
NOTE:
The first line of each code indicates the factory default.
Code
Explanation
6. 06
REGULAR CYCLE PRICE
6. 06
When the d.xx is set to d.00, this 6.xx value represents
the number of coins (coin 1) needed to start the dryer;
may adjust from 0–39. Change this value by pressing
the COTTON/WHITES button. 6.06 = 6 coins = $1.50.
(9160 models default to 6.00.)
6. 01
When the d.xx is set to d.CS, this 6.xx value
represents the number of push-in actuations of the
coin slide to start the dryer. 6.01 would equal one coin
slide activation.
• Press the PERM PRESS button once to advance
to next code.
7. 05
REGULAR DRY TIME
7. 05
When set to Coin Drop or Card Reader operation, the
dry time equals the Regular Dry Time value multiplied
by the Regular Cycle Price value. Example: 6.06 and
7.05 = (06 x 05 = 30 minutes).
7. 45
For coinslide or OPL operation, the value is the
amount of minutes of dry time. Factory default of 45
minutes. Pressing COTTON/WHITES adjusts the value
from 1–99 minutes.
• Press the PERM PRESS button once to advance
to next code.
8. 00
TYPE OF DRYER PRICING
8. 00
Fixed Cycle with Top Off. Only available for use with
coin drops or card readers. For detailed description,
see “General User Information.”
8. FC
Fixed Cycle. For detailed description, see General
User Information. Use COLORS/DELICATES button
to make this selection.
• Press the PERM PRESS button once to advance
to next code.
9. 00
CYCLE COUNTER OPTION
This option is either NOT SELECTED “OFF”
or SELECTED “ON.”
9. 00
Not Selected “OFF.”
9. 0C
Selected “ON” and not able to be deselected.
• Press the COLORS/DELICATES button
3 consecutive times to select “ON.” Once
selected “ON” it cannot be deselected.
• Press the PERM PRESS button once to advance
to next code.
1. 00
MONEY COUNTER OPTION
This option is either NOT SELECTED “OFF”
or SELECTED “ON.”
1. 00
Not Selected “OFF.”
1. 0C
Selected “ON.”
• Press the COLORS/DELICATES button
3 consecutive times to select “ON” and 3
consecutive times to deselect (Not Selected “OFF”).
Counter resets by going from “OFF” to “ON.”
1. C0
Selected “ON” and not able to be deselected.
• To select “ON” and not able to be deselected,
first select “ON;” then within 2 seconds press the
COLORS/DELICATES button twice, the COTTON/
WHITES button once, and exit set-up mode.
• Press the PERM PRESS button once to advance
to next code.
