background image

5

Recessed or closet installation - Dryer only

Recessed or closet installation - Stacked

Mobile Home - Additional Location Requirements

This dryer is suitable for mobile home installations. The
installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 245, HUD Part 280) or Standard CAN/CSA-Z240
MH.

Mobile home installations require:

Metal exhaust system hardware which is available for
purchase from your dealer.

Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.

Electrical Requirements

A 120-volt, 60-Hz., AC-only, 15- or 20-amp fused electrical
supply is required.

A time-delay fuse or circuit breaker is recommended. Be sure
fuse or circuit breaker matches the rating of your line.

Use a separate circuit serving only your dryer.

Do not use an extension cord.

A. Side view - closet or confined area
B. Recessed area

A. Recessed area
B. Side view - closet or confined area

C. Closet door with vents

B

A

     3"
(76 mm)

     14"
(356 mm)

18"(457 mm)

 0"
(0 mm)

      0"
(0 mm)

DRYER

WASHER

      (76 mm)

 3"

   (305 mm)

  12"

   (305 mm)

  12"

0"

(0 mm)

     0"

(0 mm)

B

A

C

1"

(25 mm)

     3"

(76 mm)

48 in.

2

(309.7 cm )

2

24 in.

2

(154.8 cm )

2

     3"

(76 mm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,
fire, or electrical shock.

WARNING

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or 
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes 
and ordinances.

WARNING:

Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative
or personnel if you are in doubt as to whether the dryer is 
properly grounded. Do not modify the plug provided with the 
dryer: if it will not fit the outlet, have a proper outlet installed 
by a qualified electrician.

Closet installation with WFC7500VW - Stacked

A. Recessed area
B. Side view - closet or confined area

C. Closet door with vents

DRYER

WASHER

      (51 mm)

 2"

   (25 mm)

  1"

   (0 mm)

  0"

0"

(0 mm)

     0"

(0 mm)

B

A

C

1"

(25 mm)

     3"

(76 mm)

48 in.

2

(309.7 cm )

2

24 in.

2

(154.8 cm )

2

     3"

(76 mm)

SHELF

Summary of Contents for WFC7500VW














Reviews: