Whirlpool WFG371LVQ Installation Instructions Manual Download

Page: 13 / 20

GAS CONVERSIONS

Gas conversions from Natural gas to LP gas or from LP gas to
Natural gas must be done by a qualified installer.

LP Gas Conversion

1. Turn the manual shutoff valve to the closed position.

2. Unplug range or disconnect power.

To Convert Gas Pressure Regulator (Natural Gas to
LP Gas)

1. Remove storage drawer or warming drawer. See “Storage

Drawer” or “Warming Drawer” section.

2. Locate gas pressure regulator at rear of storage or warming

drawer compartment.

NOTE: On models with a warming drawer, an access cover
must be removed to access the gas pressure regulator.

IMPORTANT: Do not remove the gas pressure regulator.

3. Remove plastic cover from gas pressure regulator cap.

4. Turn gas pressure regulator cap counterclockwise with a

⁵⁄₈

" combination wrench to remove.

NOTE: Do not remove the spring beneath the cap.

5. Turn over the gas pressure regulator cap and reinstall on

regulator so that the hollow end faces out and the marking
“

LP” is facing the direction shown in the above drawing.

6. Replace plastic cover over gas pressure regulator cap.

A. To range
B. Manual shutoff valve “closed” position

C. Gas supply line

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.

Examples of a qualified person include:

licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.

Failure to do so can result in death, explosion, or fire.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death
or serious burns to children and adults.

A. Gas pressure regulator

A. Plastic cover
B. Gas pressure regulator cap with solid end facing out

C. Gas pressure regulator cap with hollow end facing out
D. Washer

E. Gas pressure regulator cap

Side view before

Side view after

Summary of Contents for WFG371LVQ




















Search results

Summary of Contents for WFG371LVQ

Reviews:

Related manuals for WFG371LVQ

Brands by name

Popular brands

Whirlpool WFG371LVQ, Installation Instructions Manual

Search results

Summary of Contents for WFG371LVQ

Reviews:

Related manuals for WFG371LVQ

Brands by name

Popular brands