16
■
Adjust Dryness and/or Options.
NOTE
: Dryness level selections can be made only while
using Auto Cycles. Selecting More Dry, Normal or Less
Dry automatically adjusts the sensed time needed.
Auto Dry cycles take the guesswork out of drying time
and enhances fabric care. The amount of time that is
displayed is the estimated time remaining in the cycle.
To use a Manual Cycle
■
Point the dial to a Manual Cycle.
■
Press TIMING Up or Down until the desired drying time is
displayed. Tap TIMING Up or Down, and the time will
change by 1-minute intervals. Press and hold TIMING Up
or Down, and the time will change by 5-minute intervals.
NOTE:
The Timing feature can be used only with Manual
Cycles.
■
Press TEMP ADJUST until the desired temperature
illuminates.
To make changes to Time, Temperature, WRINKLE
SHIELD™ feature and Cycle Signal during a Manual
Cycle:
■
Press PAUSE/CANCEL once.
■
Adjust the Time, Temperature, WRINKLE SHIELD™
feature and End of Cycle Signal.
5.
(OPTIONAL STEP) If desired, select WRINKLE SHIELD™
feature. For more details, see “WRINKLE SHIELD™ Feature”
in “Additional Features.”
6.
(OPTIONAL STEP) The Cycle Signal is preset to ON. If
desired, you may turn the Cycle Signal OFF.
7.
Press and hold START for approximately 1 second until dryer
starts. Be sure the door is closed.
■
If you do not press Start within 5 minutes of selecting a
cycle, the dryer automatically shuts off.
Stopping or Restarting Your Dryer
To pause/stop the dryer at any time
Open the door or press PAUSE/CANCEL once.
To restart the dryer
Close the door. Press and hold START until dryer starts.
To cancel your dryer at any time
Press PAUSE/CANCEL twice.
NOTE
: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes. If the cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Select new cycle settings before restarting the dryer.
Lock Controls
This feature allows you to lock your settings to avoid unintended
use of the dryer. You can also use the control lock feature to
avoid unintended cycle or option changes during dryer operation.
To enable the control lock feature:
Press and hold END OF CYCLE SIGNAL button for 3 seconds.
The Lock/Unlock Control icon lights up, and a single beep tone is
heard. To unlock, press and hold END OF CYCLE SIGNAL button
for 3 seconds. The indicator light turns off.
Drying and Cycle Tips
Select the correct cycle and dryness level or temperature for your
load. If an Auto Cycle is running, the display shows the estimated
cycle time when your dryer is automatically sensing the dryness
level of your load. If a Manual Cycle is running, the display shows
the exact number of minutes remaining in the cycle.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
■
Follow care label directions when they are available.
■
If desired, add a fabric softener sheet. Follow package
instructions.
■
Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent
press, knits and synthetic fabrics.
■
Avoid drying heavy work clothes with lighter fabrics. This
could cause overdrying of lighter fabrics, leading to increased
shrinkage or wrinkling.
Cycle tips
■
Dry most loads using the preset cycle settings.
■
Refer to the Auto or Manual Preset Cycle Settings chart (in
the “Cycles” section) for a guide to drying various loads.
■
Drying temperature and Dryness are preset when you
choose an Auto Cycle. You can choose a different
dryness level, depending on your load by pressing the
DRYNESS button to select MORE DRY or LESS DRY.
■
If you wish to adjust the cycle length of a Manual Cycle,
you must press TIMING Up or Down. Adjust the
temperature of a Manual Cycle by pressing TEMP
ADJUST until the desired temperature is selected.
NOTE:
You cannot choose a Dryness Level with Manual
Cycles.
Status Lights
You may follow the progress of your dryer with the drying Status
indicator lights.
Sensing
When a cycle is first turned on, the SENSING light illuminates
until a wet item is detected.
■
In an Auto Cycle, if a wet item has not been detected within
5 minutes, the Sensing light will turn off.
