background image

15

5. Using UL listed wire nuts, connect the field supply wires to 

the furnace (black to black and white to white).

 

    

6. Connect ground wire to green ground screw.

7. Replace the furnace electrical connection box cover and 

screw.

Make Gas Connections

IMPORTANT: This furnace requires conversion for use with 
propane. To order the correct conversion kit, see “Accessories.”

1. Install the field gas supply as shown.

2. Provide a sediment trap on the outside of the furnace.

3. Install a manual gas shutoff valve in the gas line, outside the 

furnace, 5 ft above the floor, or in accordance with any local 
codes.

4. Install a test gauge connection with a 

¹⁄₈

" NPT plugged tap 

immediately upstream of the manual gas shutoff valve as 
shown.

5. Connect the gas pipe to the furnace controls providing a 

ground joint union as close to the controls as possible to 
facilitate removal of controls and manifold.

Pipe-joint compounds suitable for use with Natural and LP 
gas must be used. Do not use Teflon

®

 tape.

6. Turn off the gas supply at the manual gas shutoff valve.

A. Connect white to white and black to black
B. Green ground screw

WARNING

Electrical Shock Hazard

Electrically ground furnace.

Connect ground wire to green ground screw.

Failure to do so can result in death or electrical shock.

A

B

A.

¹⁄₈

" NPT plugged tap

B. Manual gas shutoff valve

C. Ground joint union
D. Tee

E. Sediment trap
F. Cap

G. Gas control valve 

(inside furnace)

A. Closed valve
B. Open valve

®Teflon is a registered trademark of E.I. Dupont de Nemours and 

Company.

B

C

D

E

F

G

A

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow the safety warnings exactly could result 
in serious injury, death or property damage. 

Never test for gas leaks with an open flame. Use a 
commercially available soap solution made specifically 
for the detection of leaks to check all connections. A fire 
or explosion may result causing property damage, 
personal injury or loss of life.

A

Summary of Contents for WGFBLT





























Reviews: