background image

FURNACE INSTALLATION INSTRUCTIONS

For Package Gas Electric Units

FURNACE SAFETY

Table of Contents

FURNACE SAFETY.........................................................................1

INSTALLATION REQUIREMENTS ................................................2

Tools and Parts ............................................................................2
Location Requirements ................................................................3
Duct Work Requirements.............................................................3
Electrical Requirements  ..............................................................4
Gas Supply Requirements ...........................................................4

INSTALLATION INSTRUCTIONS ..................................................4

Inspect Shipment .........................................................................4
Place Furnace in Final Location...................................................5
Convert to Downflow ...................................................................5
Exhaust Vent Assembly ...............................................................5

Connect Condensate Drain..........................................................6
Install Duct Work ..........................................................................6
Make Electrical Connections .......................................................7
High Altitude Conversion .............................................................8
Make Gas Connections................................................................9
Check the Furnace Input Rate ...................................................11
Complete Installation..................................................................11
Sequence of Operation ..............................................................12
Controls ......................................................................................13

TROUBLESHOOTING ..................................................................13

ASSISTANCE OR SERVICE .........................................................16

Accessories ................................................................................16

20462103

Whirlpool

®

 Home Cooling and Heating

7901 S.W. 6th Court

Plantation, Florida  33324

Model  WPG

You can be killed or seriously injured if you don't
immediately follow instructions.

You can be killed or seriously injured if you don't
follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:

Summary of Contents for WPG

















Reviews: