background image

Page 14

16940-2-0806

PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.

  14 

R-6468 

FRONT LOG - AVFBH-30

  15 

11942 

REFLECTOR ASSEMBLY  

 

- AVFBH-30 (INCLUDES 11)

  15 

12876 

REFLECTOR ASSEMBLY  

 

-  AVFBL-30 (INCLUDES 11)

  16 

11843 

SCREEN ASSEMBLY

  17 

11946 

CASING FRONT ASSEMBLY 

- AVFBH-30 ONLY (INCLUDES 

BRASS LOUVERS)

  17 

11927 

CASING FRONT ASSEMBLY - 

AVFBL-30 ONLY

 NOT SHOWN 

11937 

TUBING ASSEMBLY - INLET 

REGUALTOR TO VALVE

 NOT SHOWN 

11938 

TUBING ASSEMBLY - VALVE TO 

BURNER

 NOT SHOWN 

11941 

TUBING ASSEMBLY - VALVE TO 

PILOT

 NOT SHOWN 

R-2390 

IGNITOR WIRE

 NOT SHOWN 

P-214 

ORIFICE - LP

 NOT SHOWN 

P-270 

ORIFICE - NAT

 NOT SHOWN 

P-212 

ORIFICE HOLDER

NOT SHOWN 

R-6573 

STANDOFF (2 REQUIRED)

NOT SHOWN 

R-2685 

MIN. RATE SCREW LP 1.30

NOT SHOWN 

R-2684 

MIN. RATE SCREW NAT 2.30

 

 USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.

 Index 

  Part

 No. 

Number 

Description

 Index 

  Part

 No. 

Number 

Description

AVFBH-30 AND AVFBL-30 PARTS LIST
  1 

11847 

WALL BRACKET

  2 

R-2313 

PIEZO IGNITOR

  3 

11928 

CASING  ASSEMBLY

  4 

SR-113 

VALVE BRACKET

  5 

12274 

VALVE ASSEMBLY - NAT ONLY

  5 

12275 

VALVE ASSEMBLY - LP ONLY

  6 

11844 

UPPER SHIELD

  7 

R-2882 

CABLE CLIP

  8 

11845 

BURNER REGULATOR BRACKET 

(2 REQ’D)

  9 

R-6419 

BURNER

  10 

R-6462 

ODS PILOT ASSEMBLY - NAT ONLY

  10 

R-6463 

ODS PILOT ASSEMBLY - LP ONLY

  11 

11851 

FRONT LOG SUPPORT - AVFBL-30 

ONLY

  11 

11846 

FRONT LOG SUPPORT - AVFBH-30 

ONLY

  12 

R-2784 

INLET REGUALTOR - NAT ONLY

  12 

R-2480 

INLET REGULATOR - LP ONLY

  13 

R-6467 

REAR LOG - AVFBH-30 AND 

AVFBL-30

PARTS LIST

Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through 

the distributor. Parts can be shipped directly to the service person/dealer.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your 

equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate 

illustration and list. Be sure to give all this information.
Furnace Model Number                     

 

 

 

Part Description

Furnace Serial Number   

 

 

 

 

Part Number

Type of Gas (Propane or Natural) 
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store. 
Shipments contingent upon strikes, fires and all causes beyond our control.

HOW TO ORDER REPAIR PARTS

 Empire Comfort Systems, Inc.  Nine Eighteen Freeburg Ave.  Belleville, Illinois 62222-0529   

Summary of Contents for AVFBH-30





















Reviews: