background image

Page 1

INSTALLATION  INSTrucTIONS 

AND  OwNer'S  MANuAL 

The Breckenridge 

Select Vent-Free universal Fireboxes 

DO  NOT  ATTeMpT  TO  MODIFy  Or  ALTer  The 

cONSTrucTION OF The FIreBOx Or ITS cOMpO-

NeNTS.  ANy  MODIFIcATION  Or  ALTerATION  OF 

cONSTrucTION  MAy  VOID  The  wArrANTy  OF 

ThIS FIreBOx.
chILDreN AND ADuLTS ShOuLD Be ALerTeD TO 

The hAzArDS OF hIgh SurFAce TeMperATure 

AND  ShOuLD  STAy  AwAy  TO  AVOID  BurNS  Or 

cLOThINg IgNITION.
yOuNg  chILDreN  ShOuLD  Be  cAreFuLLy  Su-

perVISeD wheN They Are IN The SAMe rOOM 

AS The FIreBOx.

FOr uSe ONLy wITh A LISTeD gAS-FIreD uN-

VeNTeD DecOrATIVe rOOM heATer NOT TO 

exceeD 40,000 BTu/h.

DO NOT BuILD A wOOD FIre.

uNIVerSAL FIreBOx FOr ALL 

VeNT-Free LOg SeTS

MODeLS

VFS32FB2DF-3 VFS36FB2DF-3 VFS42FB2DF-3
VFS32FB3DF-3 VFS36FB3DF-3 VFS42FB3DF-3
VFS32FB2EF-2 VFS36FB2EF-2 VFS42FB2EF-2
VFS32FB3EF-2 VFS36FB3EF-2 VFS42FB3EF-2

wArNINg:    Improper  installation,  adjustment,  altera-

tion, service or maintenance can cause injury or property 

damage. refer to this manual. For assistance or additional 

information, consult a qualified installer, service agency or 

the gas supplier.

carefully review the instructions supplied with the decora-

tive type unvented room heater for the minimum fireplace 

size requirement.

DO NOT INSTALL A VeNT-Free LOg SeT IN ThIS 

FIreBOx,  uNLeSS  ThIS  FIreBOx  MeeTS  The 

MINIMuM  DIMeNSIONS  reQuIreD  FOr  The 

INSTALLATION.

GAS-FIRED

ANSI  z21.91  Ventless  Fireplace  enclosures  for  gas  Fired 

Decorative Type unvented room heaters

—  Do not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other appli-

ance.

—  whAT TO DO IF yOu SMeLL gAS

 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch; do not use any 

phone in your building.

 

•  Immediately call your gas supplier from a neigh

-

bor’s  phone.  Follow  the  gas  supplier’s  instruc-

tions.

 

•  If you cannot reach your gas supplier, call the fire 

department.

—  Installation and service must be performed by a quali-

fied installer, service agency or the gas supplier.

wArNINg: If the information in these instructions are 

not followed exactly, a fire or explosion may result caus

-

ing property damage, personal injury or loss of life.

Installer: 

Leave this manual with the appliance.

consumer:  retain this manual for future reference.

Summary of Contents for FS36FB3EF-3

















Reviews: