White Mountain Hearth FS36FB3EF-3 Owner'S Manual Download

Page: 12 / 16

25233-0-0109

Page 12

cAuTION: ALL wIrINg ShOuLD Be DONe By A QuALIFIeD eLecTrIcIAN AND ShALL Be IN cOMpLIANce

wITh ALL LOcAL, cITy AND STATe BuILDINg cODeS. BeFOre MAKINg The eLecTrIcAL cONNecTION,

MAKe Sure ThAT MAIN pOwer SuppLy IS DIScONNecTeD. The AppLIANce, wheN INSTALLeD, MuST Be

eLecTrIcALLy grOuNDeD IN AccOrDANce wITh LOcAL cODeS Or, IN The ABSeNce OF LOcAL cODeS,

wITh The NATIONAL eLecTrIcAL cODe ANSI/NFpA 70 (LATeST eDITION)

a factory installed junction box is located on the lower right

hand side of the firebox. Wiring must be fed to the junction

box and attached to the receptacle that is provided. Remove the

knockout in the installed junction box to accept wiring into the

junction box. install a UL listed cable clamp (not supplied) in the

knockout hole. Leave approximately 6" of wire in the junction

box for connection.
attach black wire to one side of the receptacle and white wire to

opposite side of receptacle. the ground wire should be attached

to the green (neutral) screw.
install the receptacle into the junction box. attach cover plate.

Keep the control compartment, logs and burner area surrounding the

logs clean by vacuuming or brushing area at least twice a year.
tHE LogS can gEt VERY Hot – HanDLE onLY WHEn

cooL.
always turn off gas to the pilot before cleaning. For relighting,

refer to lighting instructions located on the log set.

Never obstruct the flow of the combustion and ventilation air. Keep

the front of the firebox clear of all obstacles and materials.

Screens must be closed during operation.

Figure 20

JUnction BoX WiRing inStaLLation inStRUctionS

MaintEnancE

INDex

NO.

pArT NuMBer.

DeScrIpTION

VFS32FB2DF

VFS32FB3DF

VFS32FB2eF

VFS32FB3eF

17247

toP StanDoFF

10554

FRaMing BRacKEt

17162

JUnction BoX aSSEMBLY

R3492

Receptacle

R3491

coVER, JUnction BoX

19945

BRacKEt, toP BRicK REtainER

R8667

R9422

BRicK PanEL RigHt

BRicK PanEL BacK

BRicK PanEL LEFt

20020

HooD

R7051

RoD, ScREEn

R8213

ScREEn cURtain

19401

BRacKEt, BottoM BRicK REtainER

R9292

HEaRtH LEDgE, RigHt

R9293

HEaRtH LEDgE, LEFt

R9294

HEaRtH LEDgE, cEntER

23004

REtainER, HEaRtH LEDgE

PaRtS LiSt

Summary of Contents for FS36FB3EF-3

















Search results

Summary of Contents for FS36FB3EF-3

Reviews:

Related manuals for FS36FB3EF-3

Brands by name

Popular brands

White Mountain Hearth FS36FB3EF-3, Owner'S Manual

Search results

Summary of Contents for FS36FB3EF-3

Reviews:

Related manuals for FS36FB3EF-3

Brands by name

Popular brands