background image

25233-0-0109

Page 5

Select Vent-Free Firebox Framing Dimensions (in inches)

"A"

"B"

"C"

Model

Framing Height

Framing Width

Framing Depth

VFS32FB

41 1/2"

35"

23"

VFS36FB

41 1/2"

40"

23"

VFS42FB

41 1/2"

44"

23"

Attention:

 Add 3-3/4" to "A" Dimension when using flush mantel base.

Framing dimension A includes a three inch clearance for standoffs on firebox.

any vent-free gas Log Heater must be “For use with approved 

anSi Z21.11.2 unvented room heater.”
Follow and complete the installation instructions of the gas log set 

and the requirements of this firebox.
Check all fittings for leaks before lighting the gas log set.
In  planning  the  installation  for  the  firebox,  it  is  necessary  to 

determine where the unit is to be installed and whether optional 

accessories are desired. gas supply piping should also be planned 

at this time.

A gas shut off must be in this line.

The firebox can be mounted on any of these surfaces:

1.  A flat hard combustible or non-combustible surface.

2.  a  raised  platform  of  combustible  or  non-combustible 

material.

3.  Recessed into the floor as illustrated by

 Figure 4

.

4.  Supported under all (4) corners of the firebox so that contact 

is made on all four perimeter edges on the bottom of the unit 

(Example: Four (4) concrete masonry blocks).

if  the  firebox  is  installed  directly  on  carpeting,  tile  or  other 

combustible material other than wood flooring, it should be installed 

on a metal or wood panel extending the full width and depth of 

the unit.
at this point, you should have decided what components to include 

in your installation, and where the firebox is to be located. If this 

has not been done, stop and consult your dealer for assistance with 

this planning.

planning your Installation

accessory kits such as the FBB5 Blower kit, trim kits, Mantles, 

Full cabinet Mantels, plus other Decorative Frame, Hood, and 

Door accessory kits may be installed after the firebox is secured 

to the framed opening.

Refer  to  the  instructions  provided  with  each  of  the  optional 

accessory kits for proper installation and operation.

Firebox Framing

Firebox  framing  can  be  built  before  or  after  the  firebox  is  set 

in  place.  Framing  should  be  positioned  to  accommodate  wall 

covering and firebox facing material. The firebox framing should 

be constructed of 2 x 4 lumber or heavier. the framing headers may 

rest on the top of the firebox standoffs. Refer to 

Figures 5 and 6

 

for firebox framing dimensions.

LOUVERED

FIREBOX

MODELS

COMBUSTIBLE MATERIALS ALLOWED

Figure 4

Figure 5

FiREBoX inStaLLation inStRUctionS

Summary of Contents for FS36FB3EF-3

















Reviews: