background image

10

5

Maintaining 

Your Lawn 

Mower

WARNING

Always stop engine, 
disconnect spark 
plug, and ground 
against engine before 
cleaning, lubricating 
or doing any kind of 
maintenance on your 
machine.

WARNING: Always stop engine, 
disconnect spark plug, and ground 
against engine before cleaning, 
lubricating or doing any kind of 
maintenance on your machine.

Lubrication

1.  Lubricate pivot points on the blade control handle at 

least once a season with light oil. The blade control 
must operate freely in both directions. See Figure 3.

2.  Lubricate the wheels at least once a season with 

light oil (or motor oil). If  wheels are removed for any 
reason, lubricate surface of the axle bolt and inner 
surface of the wheel with light oil. See Figure 3.

3.  Lubricate the torsion spring and pivot point on the 

chute deflector periodically with light oil to prevent 
rust. See Figure 3. 

4.  Follow the accompanying engine manual for lubrica-

tion schedule and instruction for engine lubrication.

Cleaning Mower

Clean underside of the mower deck after each 
use to prevent build-up of grass clippings or other 
debris. Follow steps below for this job.

1.  Disconnect spark plug wire. Drain gasoline from lawn 

mower, or place a piece of plastic under the gas cap.

2.  Tip the mower so that it rests on the housing. Keep 

the side with the air cleaner facing up. Hold the 
mower firmly.

WARNING: Never tip the mower more 
than 90 degrees in any directions and 
do not leave the mower tipped for any 
length of time. Oil can drain into the 
upper part of the engine causing a 
starting problem.

3.  Scrape and clean the underside of the deck with a 

suitable tool. Do not spray with water. 

4.  Put the mower back on its wheels on the ground. If 

you had put plastic under the gas cap earlier, make 
sure to remove it now.

General Recommendations

1.  Always observe safety rules when performing  

any maintenance.

2.  The warranty on this lawn mower does not cover 

items that have been subjected to operator abuse 
or negligence. To receive full value from warranty, 
operator must maintain the lawn mower as  
instructed here. 

3.  Changing of engine-governed speed will void  

engine warranty. 

4.  All adjustments should be checked at least once 

each season.  See the engine owner’s manual 
included with this lawn mower.

5.  Periodically check all fasteners and make sure these 

are tight.

We do not recommend 
the use of pressure 
washers or garden 
hose to clean your 
unit. These may cause 
damage to electric 
components, spindles, 
pulleys, bearings, or 
the engine. The use 
of water will result in 
shortened life and 
reduce serviceability.

Figure 3

Lubricate these Points

Summary of Contents for 105

















Reviews: