background image

Using The Whirlpool

3

USING THE WHIRLPOOL

Before Placing the Whirlpool In Service:

Operators using the whirlpool need:

Ÿ

Personnel who will work with the whirlpool need to read 

this manual.

Ÿ

Have  a  plumbing  professional  install  the  whirlpool  as 

instructed in 

 page 4. A rough-in 

drawing  is  available  to  assist  the  installer.  Contact 
Whitehall  Customer  Service,  bottom  of  page,  for 
additional installation not covered in this manual.

Ÿ

Confirm  that  the  whirlpool  operates  properly.  See

 

Inspecting the Whirlpool

 , page 2.

Installing the Whirlpool

,

General Guidelines for Use:

Ÿ

Medical  advice  is  beyond  the  parameters  of  this 

manual.

Ÿ

The whirlpool is for professional use only. A minimum of 

one trained operator is required.

Ÿ

The  trained  operator  must  evaluate  and  verify  that  the 

patient  is  suitable  for  hydrotherapy  treatment  before 
beginning  hydrotherapy  with  whirlpool.  See 

Patient 

Evaluation

, page 2.

Ÿ

Follow  your  state  and  local  hydrotherapy  procedures 

and,  if  the  patient  has  one,  the  physician's  order  for 
treatment (see 

Patient Evaluation

, page 2).

Ÿ

Stay with patient at all times.

Ÿ

It is the operators responsibility to ensure safe practices 

for the patient and themselves.

Ÿ

If a turbine is used:

Plug  the  turbine  cord  only  into  a  receptacle  that  is 
voltage-matched,  properly  grounded  and  polarized. 
Verify that the receptacle has GFI protection or order a 
GFCI plug for the  turbine cord.

Keep patient hair, gown strings and other loose items 
away from the impeller housing to avoid entanglement 
and injury.

Keep   the area around the turbine clear. The turbine 
requires a minimum of 24" (610mm) of clearance.

Ÿ

Avoid prolonged contact with the motor cover, as elevated 

temperatures can cause discomfort.

Ÿ

Ambient  temperatures  during  use  should  not  exceed 

95°F (35°C).

WARNING

!

Certain medical conditions are incompatible with 
hydrotherapy. The trained operator is responsible for 
determining each user's suitability for hydrotherapy 
before beginning treatment.

Improper operation can cause injury. Operate the 
whirlpool only as described in this manual.

An unattended patient can be injured. Stay with 
patient at all times.

Loose items such as gown straps or gauze can be 
pulled into the turbine impeller and cause injury. Keep 
loose items away from the turbine impeller housing.

Important

Communicate with patient at all times. If a turbine is 
used, tell the patient before starting or stopping the 
turbine and before changing the water or aeration 
level.

Summary of Contents for E-27-S



































Reviews: