background image

 Sierra Super Trac Owner’s Guide

1. Trigger (on bottom of Hand Grip)

CENTER POSITION “Search” -

With the two position spring loaded Trigger on the hand grip in the center, the 

ST 

is in the 

Search Posi-

tion.

 In this position 

ALL 

metal targets will produce an Audio Response from a menu of seven different tones 

which relate to the 

VDI 

numbers which appear on the Visual Display.  

IRON

 produces the 

“Lowest Tone” 

(Grunt)

 thru 

COINS 

 the 

Highest Tones

. This feature makes the detectorist 

immediately aware

 of 

the likely category of the metal item 

without having to watch the Visual Display while search-

ing

. Each of the seven tones relates to the group of Display Categories as shown on the diagram at the bottom 

of 

page 4. Gold jewelry

 will make a clearly 

higher tone

 than the 

Iron Grun

t but 

Lower than

 the 

high coin tones. After hearing the

 Tone Alert, THEN

  stop to look at the 

Visual Display

 for more informa-

tion before deciding whether or not to dig the target. 

Personally, I usually dig ALL targets which 

are NOT clearly Iron. In this way I don’t miss any good targets.

 As you get more experience, 

however, you will be able to sort out the different higher sounds along with watching the 

VDI numbers

 dis-

played on the screen and be able to ignore some of the 

“non iron”

 pieces of trash.

SQUEEZED POSITION “PINPOINTING & DEPTH READING”

After deciding you wish to dig the target, 

Squeeze and Hold the spring loaded Trigger

 on the hand 

grip and crisscross the target as shown on the bottom of page 2. At this time the display will also indicate the ap-

proximate depth of a coin sized target in inches. 

Once released the trigger will automatically return 

to the Center “Search” position.

It will also be noted, that while the 

Pinpoint Trigger

 is 

squeezed

, the 

Sierra ST will STOP Track-

ing. It is very important to prevent tracking during pinpointing

 as repeated passes while Xing 

over the target may cause the tracking system to track 

INTO

 the target and diminish the signal smaller or deeper 

targets. 

  

Controls-

Trigger control 

on the hand grip

P/P

Search

Summary of Contents for Sierra Super Trac











Reviews: