Whitfield Profile 20 FS-2 Installation And Operation Manual Download

Page: 9 / 48

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Figure 10 - Damper Adjustment, Free-Standing Models

nstalling Surround Assembly

Profi le

30 INS-2

(to be done after venting system is installed)

This fi replace insert

requires surround panels (a set of metal panels that enclose the fi replace
opening when fi tted together). There is also a trim assembly that frames
the surround assembly to give it an attractive fi nished appearance. Put
the surround assembly together according to the following instructions
(ref.

Page 41

)

1. Remove panels and trim brackets from package. Be careful not to

discard the “L” shaped trim brackets which are attached to the sur-
round wrapping.

2. Open the hopper lid of the insert so it is out of the way for when panels

are installed.

3. Install the control board onto the right side panel (with door) using

the TEK screw (#8 x 1/2”) provided.

4. Position the power cord so that it will be behind either the right or left

side surround panel when they are installed.

5. Install right side surround panel onto right side of the insert body by

sliding the 2 fl anges on side of panel into corresponding slots on the
insert.

6. Connect the wiring harness from the insert into corresponding con-

nector on control board.

7. Locate damper rod on left side of the insert. Rotate angled arm of rod

so it is pointing down. Remove damper knob and set aside.

8. Install the left-hand panel onto the left side of the insert body by

sliding the 2 fl anges on side of panel into corresponding slots on the
insert.

9. Reach behind left surround panel and rotate damper arm so that end

is inserted into the upper right hand slot of left surround panel (see

Figure 11

10. Reinstall damper knob by threading it onto end of damper rod.
11. Set the top surround panel in place over the two side panels. Posi-

tion the 2 tabs on bottom of top surround panel so they slide into
corresponding clips on the insert. Connect the top surround panel to
the side panels by pressing pins from side panels into corresponding
holes on top panel.

12. Remove the surround trim from its packaging. Assemble it together

using the corner keys (“L” shaped brackets) provided. Slide assembled
trim over the top surround panel and slide it down over the side
panels.

13. Push the Profi le 30 INS-2 back into place so the surround assembly

is fl ush with the face of the hearth.

Damper Location, Installation And Adjustment

Damper Air Control Handle - Models: Profi le 20 FS-2 and Profi le 30 FS-2

(located on right side panel on model Profi le 20 FS-2 and on the left side
panel on Profi le 30 FS-2)

Adjustment Procedure- Models: Profi le

20 FS-2 and Profi le 30 FS-2

Loosen setscrew on set collar (see

Figure 10

then adjust in 1/4” incre-

ments until optimum combustion air fl ow is achieved. For less air push
in and for more air pull out. After adjustment, position set collar against
side panel and tighten setscrew.

Damper is factory set to a
gap as specifi ed below.

1-5/8” - Profi le 30 FS-2
2” - Profi le 20 FS-2

To adjust, use a 3/32” allen
wrench (provided with stove)
to loosen set collar.

Damper Installation - Model: Profi le 30 INS-2

Install damper rod knob as illustrated (see

Figure 11

)

and explained on

this page (see

Installing Surround Assembly – Profi le 30 INS-2)

Adjustment Procedure - Model: Profi le 30 INS-2

The damper knob should be positioned in the center of the oblong slot
for the average installation (see