background image

P.O. Box 2827

Eugene, OR 97402 USA

Outside U.S. or Canada: 541- 687- 0213

Outside U.S. or Canada: 541- 687- 0213

800-653-3336

800-653-3336

Fax: 541-687-2060 • 

Fax: 541-687-2060 • www

www.whittie

.whittierrwood.com

wood.com

Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A

Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A

For normal household use only.

 recommended for commercial use.

Congratulations!

Production Code:

Assembly Instructions

Model #

McKenzie

Queen Platform

Storage Bed

1317AFGAC

VN

Service  Policy:

 

We  will  replace  parts 

which  are  defective,  missing  or  damaged. 

Please  contact  Whittier  Wood  Products 

customer  service  department  directly  (by 

phone,  fax,  mail  or  E-mail)  for  replacement 

parts.

Hours:

 

Our friendly customer service staff 

can be reached Monday-Friday 7:00 a.m. to 

5:00 p.m. (Pacific Time). A message can be 

left 24 hours a day, 7 days a week.

To Order: 

Provide the complete furniture 

model number, part letter, production code, 

quantity  needed,  reason  for  replacement 

and your full name and address along with 

a  telephone  number  in  case  we  need  to 

contact you.

Parts ship from our Eugene, Oregon factory 

within 1 or 2 business days from the time 

we receive the request. Please allow 5-10 

business days for delivery.

This fine piece of furniture will make a handsome 

addition to your home. For the best results, start 

b

begin your project.

yy reading the Assembly Instructions 

before

 you

 

 

 

 

Unload items from this unit prior to moving.

Before loading or moving this unit, check all screws 

and supports for tightness.

Store the item: 1) in the box; 2) in a dry place; 3) in 

temperatures ranging from 40° to 90°. (Not on a cold, 

possibly damp, cement floor.)

Inspect  your  furniture  periodically  for  any  loose  glue 

joints or screws, or any other problem which may be 

affecting the stability of your furniture. Tighten or repair 

as needed.
This Assembly requires two people.

DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.

07/29/08

Summary of Contents for 1317AFGAC









Reviews: