Whittier Wood 1614AUF Assembly Instructions Manual Download

Page: 6 / 11

1614AUF; 1620AUF; 1626AUF & 1632AUF McKenzie Alder Hutch

Assembly Instructions

1614AUF_1620AUF_1626AUF_1632AUF — Page 6 — 04/17

Bookcase Tipping Restraint Instructions

Before you begin this assembly, identify each part and make sure the quantities received match what is on this

list. If you need to replace a part, contact Whittier Wood Furniture customer service and refer to the following

list for its name and letter code.

Part

Description

Quantity

Cam Buckle and Short Strap (installed)

Plastic Bracket (installed)

1" x 1000mm Long Strap (installed)

#8 x 3" Pan Head Screw

Washer (installed)

#8 x 5/8" Pan Head Screw

(1 inserted)

#8 x 1-1/4" Pan Head Screw

“L” Angle Bracket

If you have a stone or tile floor or do not wish to drive screws into the corner of the baseboard
and floor see the instruction included inside the tipping restraint kit for an alternate
installation.

Continued on Page 7

Summary of Contents for 1614AUF












Search results

Summary of Contents for 1614AUF

Reviews:

Related manuals for 1614AUF

Brands by name

Popular brands

Whittier Wood 1614AUF, Assembly Instructions Manual

Search results

Summary of Contents for 1614AUF

Reviews:

Related manuals for 1614AUF

Brands by name

Popular brands