background image

 

P.O. Box 2827 
Eugene, OR 97402 USA

 

Production Code: 
 
 
 
 
 

VN 

04/14 

 

Model # 

3461AFCAFb 

Stayton Corner 
Media Console 

AFCAF = Caffè finish

 

Assembly Instructions 

 

 

 
Congratulations! 

This fine piece of furniture will make a gorgeous addition to 
your home. For the best results, read the Assembly 
Instructions before you begin your project.

IMPORTANT NOTES: 

  For normal household use only. 

Not

 recommended for commercial use. 

  Do not climb, sit or stand on this piece of furniture. 
  Unload items before you move this unit. 
  Do not overload the drawer or shelves. 
  Before you load or move this unit, tighten all screws and supports. 
  Before you begin your project, completely read the Assembly 

Instructions. 

  Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that 

range from 40°F to 90°F (not on a cold and possibly damp cement 
floor). 

  Periodically inspect your furniture for any loose glue joints, screws or 

any other problem that might affect the stability of your furniture. 
Tighten or repair as needed.

 

  This assembly requires two people.

 

 

 

WARNING

 

Serious or fatal crushing injuries can occur from furniture tip-over. Use of 
tip-over restraints may only reduce but not eliminate the risk of tip-over. 

To help prevent tip-over: 

 

Place heaviest items in the bottom drawers. 

 

Unless specifically designed to accommodate, do not set TVs or other 
heavy objects on top of this product. 

 

Never allow children to climb or hang on drawers, doors or shelves. 

 

Never open more than one drawer at a time. 

Warning

: At least one tipping restraint kit was included with your piece of 

Whittier Wood Furniture. When you receive your furniture, be sure to find 
and properly install the tipping restraint(s). If you cannot locate the 
restraint(s), please contact us immediately for replacement. 

Notice to California Customers 

California Prop 65 requires consumer goods to be labeled if any one of 
850+ different chemicals or substances, including wood dust, is present 
even in trace amounts. Drilling, sawing, sanding or machining wood 
products generates wood dust, a substance known to the State of 
California to cause cancer. 

Warning

: This product contains a chemical 

or substance known to the State of California to cause cancer, birth 
defects or other reproductive harm. 

California Health and Safety Code 

Section 25249.6

 

 
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.

 

 CALL US FIRST! 

Do not return this item to the store

 

Service Policy:

 We will replace any part that is defective, 

missing or damaged during assembly. For a replacement 
part, directly contact Whittier Wood Products customer 
service department by phone, fax, mail or email. 
 

Hours:

 Our friendly customer service staff can be reached 

Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You 
may leave a message 24 hours a day, seven days a week.

 

To Order:

 Provide the finish and furniture model number 

(upper portion of this page), the part letter, production 
code, quantity needed, reason for replacement and your 
full name, address and telephone number. 
 

Parts ship from our Eugene, Oregon factory within one or 
two business days from the time we receive your request. 
Please allow five to ten business days for delivery.

 

800-653-3336

 

 

Outside the U.S. or Canada: 541-687-

0213 • Fax: 541-687-2060 

www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

 

 
 

Summary of Contents for 3461AFCAFb









Reviews: