background image

Weldarc 135, 145, 185   |   Operator Manual   |   Model No MC110-0 / MC111-0 / MC112-0

7

6

Walls touching combustibles on opposite 

sides should not be welded on or cut. Walls,  

ceilings, and floor near work should be 

protected by heat-resistant covers or shields.
A person acting as Fire Watcher must be 

standing by with suitable fire extinguishing 

equipment during and for some time after 

welding or cutting if;
–  Combustibles (including building 

construction) are within 10 metres.

–  Combustibles are further than 10 

metres but can be ignited by sparks.

–  Openings (concealed or visible) in floors 

or walls within 10 metres may expose 

combustibles to sparks.

–  Combustibles adjacent to walls, 

ceilings, roofs, or metal partitions can 

be ignited by radiant or conducted heat.

After work is done, check that area is free  

of sparks, glowing embers, and flames.
A tank or drum which has contained 

combustibles can produce flammable 

vapours when heated. Such a container 

must never be welded on or cut, unless 

it has first been cleaned as described in 

AS.1674.2. This includes a thorough steam 

or caustic cleaning (or a solvent or water 

washing, depending on the combustible’s 

solubility), followed by purging and inerting 

with nitrogen or carbon dioxide, and using 

protective equipment as recommended in 

AS.1674.2. Water-filling just below working 

level may substitute for inerting.
Hollow castings or containers must be 

vented before welding or cutting. They can 

explode. Never weld or cut where the air may  

contain flammable dust, gas, or liquid vapours.

Shock Prevention
Exposed conductors or other bare metal 

in the welding circuit, or ungrounded 

electrically alive equipment can fatally 

shock a person whose body becomes 

a conductor. Ensure that the equipment 

is correctly connected and earthed. If 

unsure have the equipment installed by a 

qualified electrician. On mobile or portable 

equipment, regularly inspect condition of 

trailing power leads and connecting plugs. 

Repair or replace damaged leads.
Fully insulated electrode holders should 

be used. Do not use holders with 

protruding screws. Fully insulated lock-type 

connectors should be used to join welding 

cable lengths.
Terminals and other exposed parts of 

electrical units should have insulated knobs 

or covers secured before operation.

Summary of Contents for MC110-0

































Reviews: