background image

 

Safety instructions 

 

 

Wieland Electric GmbH | BA000868 | 08/2021 (Rev. C) 

 

2

 

SAFETY INSTRUCTIONS 

This chapter is for your safety and the safety of equipment operators. Please read this chapter care-
fully before working with a VPN-Router. 

General safety 

 

Personnel which install, program, operate or maintain this device must have read and understood 

these instructions. 

 

The personnel must be thoroughly familiar with all warnings, instructions and requirements con-
tained in this manual. 

 

The applicable local safety, protection and installation requirements must be observed. 

 

The user is solely responsible for selecting the correct product and the technical design in accord-

ance with appropriate local regulations. 

2.1

 

Qualified persons 

wienet

 VPN router must be installed by competent persons only, configured in operation, commis-

sioned and maintained. Qualified is, who: 

 

has an appropriate technical training and 

 

has access to the 

wienet

 VPN router installation manuals, and this has been read and under-

stood. 

2.2

 

General safety instructions 

Please, observe the following instructions: 

 

The router must be used in compliance with all applicable international and national laws and 

in compliance with any special restrictions regulating the utilization of the router in prescribed 
applications and environments.  

 

To prevent possible injury to health and damage to appliances and to ensure that all the rele-
vant provisions have been complied with, use only the original accessories. Unauthorized modi-

fications or utilization of accessories that have not been approved may result in damage to the 
router and in a breach of applicable regulations. Unauthorized modifications or utilization of 

accessories that have not been approved may result in the termination of the validity of the 
guarantee. 

 

The router cannot be opened.  

 

Before handling the SIM card, turn off the router and disconnect it from power supply. 

 

Caution! 

The SIM card could be swallowed by small children. 

 

 

Input voltage must not exceed 36 V DC max. 

 

Do not expose the router to extreme ambient conditions. Protect the router against dust, mois-
ture and high temperature. 

 

The router should not be used at petrol stations. We remind the users of the duty to observe the 
restrictions concerning the utilization of radio devices at petrol stations, in chemical plants, or 

in the course of blasting works in which explosives are used. 

 

Switch off the router when travelling by plane. Utilization of the router in a plane may endanger 

the operation of the plane or interfere with the mobile telephone network, and may be unlaw-
ful. Failure to observe these instructions may result in the suspension or cancellation of tele-

phone services for the respective client, or, it may result in legal sanctions; it may also result in 
both eventualities. 

 

When using the router in the close proximity of personal medical devices, such as cardiac pace-
makers or hearing aids, you must proceed with heightened caution. 

 

The router may cause interference when used in close proximity to TV sets, radio receivers or 
personal computers. 

 

It is recommended that you should create an appropriate copy or backup of all the important 
settings that are stored in the memory of the device. 

 

WARNING 

 

CAUTION 

Summary of Contents for wienet LR77 v2


































Reviews: