background image

12

Contents of the packaging

Heater POW-LCD MULTI  

pcs. 1

Control valve 

pcs. 1

Fastening screws with expansion plugs  

pcs. 3

Gaskets 

pcs. 2

Template 

pcs. 1

Operating instructions 

pcs. 1

Guaranty card 

pcs. 1

IMPORTANT INSTRUCTIONS

CONCERNING THE DETERIORATED DEVICE

Pursuant to the provisions of the Act dated 29 July 2005 on waste electric and elec-

tronic equipment, it is forbidden to put together with municipal waste the deteriorated 
equipment marked with the symbol of the crossed out bin.

A user who intends to get rid of the product, should take the waste electric or 

electronic equipment to the point collecting the waste equipment. Collection points are 
run, among others, by wholesalers or retailers of such equipment as well as by gmina 
organizational units conducting the activity in the scope of collecting waste.

The above statutory obligations have been introduced in order to limit the amount 

of waste created from deteriorated electric and electronic equipment, as well as to 
ensure the proper level of collecting, recovering and recycling the waste equipment. 
In the equipment there are no dangerous elements which have a particularly negative 
effect on health and the environment.

The materials used in the device are re-usable. Thanks to re-use, re-use of materi-

als, or other forms of use of the deteriorated devices, you contribute significantly to the 
protection of our environment.

Summary of Contents for Type POW-LCD MULTI













Reviews: