WIKA CPT6020 Operating Instructions Manual Download

Page: 28 / 34

WIKA operating instructions process pressure transducer, model CPT6020

0020507001F 05/2019 EN

8. Dismounting, Return and Disposal

WARNING!

Physical injuries and damage to property and the environment through residual media

Residual media in the dismounted instrument can result in a risk to persons, the environment and equipment.

▶

Wear the requisite protective equipment (see Chapter 3.6 “Personal protective equipment”).

▶

Observe the information in the material safety data sheet for the corresponding medium.

▶

Wash or clean the dismounted instrument, in order to protect persons and the environment from exposure to

residual media.

8.1 Dismounting

WARNING!

Physical injuries and damage to property and the environment through residual media

Upon contact with hazardous media (e.g. oxygen, acetylene, flammable or toxic substances), harmful media (e.g.

corrosive, toxic, carcinogenic, radioactive), and also with refrigeration plants and compressors, there is a danger of

physical injuries and damage to property and the environment.

▶

Before storage of the dismounted instrument (following use) wash or clean it, in order to protect persons and the

environment from exposure to residual media.

▶

Wear the requisite protective equipment (see Chapter 3.6 “Personal protective equipment”).

▶

Observe the information in the material safety data sheet for the corresponding medium.

WARNING!

Risk of burns

During dismounting there is a risk of dangerously hot media escaping.

▶

Let the instrument cool down sufficiently before dismounting it!

WARNING!

▶

Power should switched off before disconnecting the device.

WARNING!

Physical injury

When dismounting, there is a danger from aggressive media and high pressures.

▶

Wear the requisite protective equipment (see Chapter 3.6 “Personal protective equipment”).

▶

Observe the information in the material safety data sheet for the corresponding medium.

▶

Only disconnect the pressure measuring instrument/measuring assembly/test and calibration installations once

the system has been de-pressurised.

Dismounting, Return and Disposal

Summary of Contents for CPT6020



































Search results

Summary of Contents for CPT6020

Reviews:

Related manuals for CPT6020

Brands by name

Popular brands

WIKA CPT6020, Operating Instructions Manual

Search results

Summary of Contents for CPT6020

Reviews:

Related manuals for CPT6020

Brands by name

Popular brands