WIKA CPT6020 Operating Instructions Manual Download

Page: 6 / 34

WIKA operating instructions process pressure transducer, model CPT6020

0020507001F 05/2019 EN

1. General Information

■

The CPT6020 Precision Pressure Transducer described in the operating instructions has been designed and manufactured

using state-of-the-art technology. All components are subject to stringent quality and environmental criteria during production.

Our management systems are certified to ISO 9001 and ISO 14001.

■

These operating instructions contain important information on handling the instrument. Working safely requires that all safety

instructions and work instructions are observed.

■

Observe the relevant local accident prevention regulations and general safety regulations for the instrument's operating range.

■

The operating instructions are part of the instrument and must be kept in the immediate vicinity of the instrument and readily

accessible to skilled personnel at any time. Pass the operating instructions onto the next operator or owner of the instrument.

■

Skilled personnel must have carefully read and understood the operating instructions prior to beginning any work.

■

The general terms and conditions contained in the sales documentation shall apply.

■

Subject to technical modifications.

■

Factory calibrations are carried out in accordance with international standards.

■

Further information:

Mensor Corporation

- Address

201 Barnes Dr., San Marcos, TX 68666

- Internet address:

www.mensor.com

- Relevant data sheet:

T 25.12

- Application consultant:

Tel.: (+1) 512-396-4200

(+1) 800-984-4200 (USA only)

Fax: (+1) 512-396-1820
E-Mail: sales@mensor.com
techservices@mensor.com

Importer for Europe

WIKA Alexander Wiengand SE & Co. KG

Address

Alexander Wiegand-Straße

63911 Klingenberg, Germany

- Internet address:

www.wika.de / www.wika.com

- Relevant data sheet:

CT 25.12

- Application consultant:

Tel.: (+49) 9372/132-5015

Fax: (+49) 9372/132-8767

E-Mail:

CTsales@wika.com

1.1 Warranty

All products manufactured by Mensor are warranted to be free of defects in workmanship and materials for a period of two year

from the date of shipment. No other express warranty is given, and no affirmation of Seller, by words or actions, shall constitute

a warranty. SELLER DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR

PURPOSES WHATSOEVER. If any defect in workmanship or material should develop under conditions of normal use and service

within the warranty period, repairs will be made at no charge to the original purchaser, upon delivery of the product(s) to the

factory, shipping charges prepaid. If inspection by Mensor or its authorized representative reveals that the product was damaged

General information

Summary of Contents for CPT6020



































Search results

Summary of Contents for CPT6020

Reviews:

Related manuals for CPT6020

Brands by name

Popular brands

WIKA CPT6020, Operating Instructions Manual

Search results

Summary of Contents for CPT6020

Reviews:

Related manuals for CPT6020

Brands by name

Popular brands