Wildix BRI Series Admin Manual Download | Manualshive

Page: 14 / 14

background image

Debugging and troubleshooting of Media Gateways

Debugging and troubleshooting of Media Gateways

Page 14 of 14

Custom encryption is enabled on W01/ W02 FXS for SIP signaling (implemented in WMS version

3.82.32840.35). Starting from WMS version 3.85.35394.9, alternative SIP port for remote registration of W01FXS

/ W02FXS is used for SIP registration (the first port from RTP range).

In some scenarios, for example, when iptables forwarding is not available, port redirect doesn't work. As a result,

W01/ 02 FXS can loss SIP registration.

Solution

Disable the encryption for devices located behind NAT/ Firewall. To implement, you need to apply the following

custom parameters to [wildixfxs] section of

:

/rw2/etc/provisioning.conf

file

SIPTransportRemote = UDP

SIPServerPortRemote = 5060

Note: Consult

Provisioning Custom Settings Guide

«
...
12
13
14

Summary of Contents for BRI Series















Reviews:

No comments

Related manuals for BRI Series

Brand: auto maskin Pages: 13

Intesis IN701-KNX Series

Brand: HMS Networks Pages: 48

PagePro VIP-204A

Brand: Valcom Pages: 4

Brand: RTA Pages: 68

WILOW-IOT-GATEWAY-4G

Brand: BEANAIR Pages: 29

Brand: ZyXEL Communications Pages: 18

Brand: McQuay Pages: 52

Brand: Berker Pages: 4

Brand: DAE Pages: 2

Brand: Motorola Pages: 28

Brand: Motorola Pages: 351

SURFboard eXtreme SBG6782-AC

Brand: Motorola Pages: 2

Brand: Samsung Pages: 20

Brand: Samsung Pages: 17

IPX-G5X0 series

Brand: Samsung Pages: 27

Brand: Samsung Pages: 27

Brand: Samsung Pages: 28

Brand: Samsung Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands