background image

CAUTION:

In cooling and dehumidifying modes, if the compressor cycle is interrupted (due to unplugging, power failure,
etc.), a protection circuit is automatically activated, preventing the compressor from operating. This is no cause
for alarm, but the protection circuit may need 3-5 minutes to reset.

Dehumidifying mode icon

Mode button

In dehumidifying mode,

- When the room temperature is below 59 °C (15 °C), this 
function is not available.

- When the room temperature is between 59 and 72 °F (15 and
22 °C), the compressor will automatically run at regular 
intervals of 6 minutes ON and 10 minutes OFF.

- When the room temperature is between 72 and 82 °F (22 and
28 °C), the compressor will automatically run at regular 
intervals of 6 minutes ON and 6 minutes OFF.

- When the room temperature is above 82 °F (28 °C), the 
compressor will automatically run at regular intervals of 10
minutes ON and 4 minutes OFF.

In this mode, the temperature and the fan speed cannot be
adjusted. The fan will automatically run at low speed.

1. Press the 

ON/OFF

button to start the air   conditioner.

2. Press the 

MODE

button repeatedly until the dehumidifying

mode icon (    ) is displayed in the upper left corner of the
remote control.

Owner’s manual _9

9_ DEHUMIDIFYING MODE

Summary of Contents for 12SRA-HE
























Reviews: