background image

(see Figure 8). The default rotation is set by using a combination of a spike, nut, and a 

diode. If required, additional rotation can be achieved by using the provided 1/2” spacers 

between the diode and the bottom of the cabinet (see Figure 8). The amount of rotation 

depends on your listening position. 

Set the rotation as follows:

1.  Remove the casters from the bottom of the Mezzo Convergent Synergy. In-

sert the spike with nut in their place. Turn to Section 10, table 1, locate your 
listening position on the table.

2.  Assemble the front spikes with the listed diode/spacer combination in Table 

1 (see also Figure 5).

3.  Install the spikes as shown in Figure 9 above.

Note: the material used for the bottom of the Mezzo Convergent Synergy Wilson’s pro-

prietary high density composite X-material. While very hard, X-material is easily cross 
threaded when installing the spikes. Be careful that the spike thread is engaging prop-
erly into the bottom.

•   4. Carefully lift the Mezzo Convergent Synergy into the desired location 

and set it down.

Note: Four small brass disks have been provided for use as spike pads. Place these under 
the spikes to protect the finish of your floors. 

•   5. Turn to Section 4.7 for final assembly instructions.

Section 4.5—Setup #2 Mezzo Convergent Synergy on a Stand

1.  Set the stand in the desired listening location.

2.  Referring to Section 4.2, attach the spikes to the bottom of the stand by 

screwing the spike and nut combination until the nut is flush with the bottom 

f

igure

 9 – i

nstalling

 

the

 M

ezzo

 c

onVergent

 s

YnergY

 s

tand

 s

pikes

t

hreaded

 S

pikeS

S

pacerS

 (

uSe

 

only

 

iF

 

indicated

 

in

 

table

)

S

pike

 

and

 

n

ut

 o

nly

d

iode

, S

pike

and

 n

ut

f

igure

 8 – i

nstalling

 

the

 M

ezzo

 c

onVergent

 s

YnergY

 s

pikes

s

e C T i O n

  4 . 5 — s

e T u p

  # 2   M

e z z O

  C

O n v e r g e n T

  s

y n e r g y

 

O n

 

a

  s

T a n d

M

e z z o

  C

o n v e r g e n t

  S

y n e r g y

  o

w n e r

S

  M

a n u a l

44

45

W i l s o n   A u d i o   S p e c i a l t i e s

W i l s o n   A u d i o   S p e c i a l t i e s

Summary of Contents for Convergent Synergy


















































Reviews: