background image

1

30-Day Money-Back Guarantee

All Wilson Electronics products are protected by Wilson’s 30-day money-back 
guarantee.  If for any reason the performance of any product is not acceptable, 
simply return the product directly to the reseller with a dated proof of purchase.

1-Year Warranty

Wilson Electronics amplifi ers are warranted for one (1) year against defects in 
workmanship and / or materials.  Warranty cases may be resolved by returning the 
product directly to the reseller with a dated proof of purchase. 

Amplifi ers may also be returned directly to the manufacturer at the consumer’s 
expense, with a dated proof of purchase and a Returned Material Authorization 
(RMA) number supplied by Wilson Electronics.  Wilson shall, at its option, either 
repair or replace the product. Wilson Electronics will pay for delivery of the repaired 
or replaced product back to the original consumer.

This warranty does not apply to any amplifi ers determined by Wilson Electronics 
to have been subjected to misuse, abuse, neglect, or mishandling that alters or 
damages physical or electronic properties.

RMA numbers may be obtained by phoning Technical Support at 866-294-1660.

The Manufacturer’s rated output power of this equipment is for single carrier operation. 
For situations when multiple carrier signals are present, the rating would have to be 
reduced by 3.5 dB, especially where the output signal is re-radiated and can cause 
interference to adjacent band users.  This power reduction is to be by means of input power 
or gain reduction and not by an attenuator at the output of the device.

Operation is subject to the following two conditions: (1) This device may not cause 
interference and (2) this device must accept any interference, including interference that 
may cause undesired operation of this device.

Disclaimer:   The information provided by Wilson Electronics, Inc. is believed to 
be complete and accurate.  However, no responsibility is assumed by Wilson 
Electronics, Inc. for any business or personal losses arising from its use, or for 
any infringements of patents or other rights of third parties that may result from 
its use.

Copyright © 2007 Wilson Electronics, Inc.  All rights reserved.

3301 East Deseret Drive, St. George UT 84790

For additional Technical Support visit

www.wilsonelectronics.com

Phone: 866-294-1660        Fax: 435-656-2432

Wilson

®

         Electronics, Inc.

Summary of Contents for 271247-50









Reviews: