background image

  8 

SM-275 

SPECIFICATIONS

 

PROBLEM 

CAUSE & SOLUTION 

No power or Main Switch not lit up 
when unit is plugged into power out-
let 

Power is not on 
—flip Main switch to ON position 
GFCI Plug not reset 
—press reset button on GFCI 
GFCI Plug defective 
Main switch defective 

Main Switch lit up but motor not 
turning when activated 

Leakage in air-activated switch system 
—defective Foot Pedal 
—defective air switches 
Defective motor 
Short-circuit of wiring  

Main Switch lit up & motor hums or 
runs only in reverse when activated. 

Defective air switches 
—replace air switch 

Motor running but Flexible Shaft not 
turning 

Broken Safety Coupling 

Motor running but no water output 
at  end of Flexible Shaft 

Water supply not turn on 
Defective Solenoid Valve 

Motor running and water drips in-
side unit 

—Worn Teflon seal inside Motor Connector 
—Leakage in tube or  tube fittings 

Unit running rough and/or noisy 

Lack of lubrication in Motor Connector 
—grease ball bearings inside Motor Connector 
through grease fitting through access hole in 
bottom of unit 
—replace worn or corroded ball bearings in 
Motor Connector 

TROUBLE-SHOOTING

 

MODEL 

9506-22

0

9600-2200 

VOLTAGE 

220 

220 

FREQUENCY 

50 

50 

HORSEPOWER 

1/2 

1/2 

RPM 

1725 

1725 

WEIGHT (LBS) 

35 

55 

DIMENSIONS 

10”H 18”W 8 1/2”D  12”H 23”W 11 1/2”D 

Thomas C. Wilson, LLC

21-11  44th Avenue, Long Island City, New York  11101 

Tel: (800) 230-2636    Fax: (718)361-2872    http://www.tcwilson.com 

E-mail: tcwilson@tcwilson.com 

 

SM-275 

Thomas C. Wilson, LLC

21-11  44th Avenue, Long Island City, New York  11101 

Tel: (800) 230-2636   Fax: (718)361-2872   http://www.tcwilson.com 

E-mail: tcwilson@tcwilson.com 

TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE 

USER MUST READ AND UNDERSTAND OPERATOR’S MANUAL. 

Rev: A, 1/20/2015 

OPERATING INSTRUCTIONS 

SERVICE MANUAL 

WILS-AWAY 

ELECTRIC TUBE CLEANER

 

   9506-22

0

   9600-2200 

Summary of Contents for 9506-2200

Page 1: ...l inside Motor Connector Leakage in tube or tube fittings Unit running rough and or noisy Lack of lubrication in Motor Connector grease ball bearings inside Motor Connector through grease fitting through access hole in bottom of unit replace worn or corroded ball bearings in Motor Connector TROUBLE SHOOTING MODEL 9506 2200 9600 2200 VOLTAGE 220 220 FREQUENCY 50 50 HORSEPOWER 1 2 1 2 RPM 1725 1725 ...

Page 2: ... lar ger than the inlet port for efficient output and speed control Protect all surrounding items from exhaust air Bearings are grease packed Use Gast AD220 or a detergent SAE 10 automotive engine oil for lubri cating Motors are to be used in commercial installations only This motors is not designed for use in hazardous atmospheres Air supply directional control valve and pressure regulator should...

Page 3: ... the shaft is overloaded by forcing cleaning tool within the tube A hook type removal tool 9600 0055 is supplied for removing this broken unit Engage the far end of the broken coupling with this tool and pull the coupling out Storage To store disconnect water supply hose and foot pedal Disconnect flexi ble shaft from machine Dry out the shaft with an air blast through a hose fitting optional 9614 ...

Page 4: ... place a mark on outside of flexible shaft to retain brush or cleaning head just within tube on opposite end 7 Place the foot pedal at a point close to the tube sheet Hold the end of the flexible shaft with one hand about three inches from the cleaning head making sure it is held away from your body and then depress the foot pedal 8 The electric motor will operate and drive the flexible shaft whic...

Reviews: