15
WILSON PRO 4000R
IN-BUILDING MULTI-ANTENNA SIGNAL BOOSTER
EN
Product Number
U460031
Model Number
460031
FCC ID
PWO460031
Connectors
N-F
emale
Antenna Impedance
50 Ohms
Frequency
698-716 MHz, 729-746 MHz, 746-756 MHz, 746-787 MHz, 824-894 MHz, 1850-1990 MHz,
1710-1755/2110-2155 MHz
Passband Gain (nominal)
700
MHz
Band12/17
57.8
700
MHz
Band13
57.8
800
MHz
59.8
1700/2100
MHz
62.5
1900
MHz
63.6
20 dB Bandwidth (MHz)
700
MHz
Band12/17
700
MHz
Band13
800
MHz
1700/2100
MHz
1900
MHz
Typical
Maximum
29.8
35.2
29.9
35.2
36.4
37.4
76.7
79.2
73.8
74.4
Power output for single cell
phone (Uplink) dBm
700
MHz
Band12/17
700
MHz
Band13
800
MHz
1700
MHz
1900
MHz
24.7
25.7
25.3
26.1
25.2
Power output for single cell
phone (Downlink) dBm
700
MHz
Band12/17
700
MHz
Band13
800
MHz
2100
MHz
1900
MHz
11.0
11.0
11.0
11.0
9.1
Power output for multiple
received channels (Uplink) dBm
No. Tones
700
MHz
Band12/17
700
MHz
Band13
800
MHz
1700
MHz
1900
MHz
2
18.0
18.3
21.1
17.6
22.1
3
14.5
14.8
17.6
14.1
18.6
4
12.0
12.3
15.1
11.6
16.1
5
10.0
10.3
13.1
9.6
14.1
6
8.5
8.8
11.6
8.1
12.6
Power output for multiple
received channels
(Downlinklink) dBm
No. Tones
700
MHz
Band12/17
700
MHz
Band13
800
MHz
2100
MHz
1900
MHz
2
11.2
12.5
14.0
11.4
10.5
3
7.7
9.0
10.5
7.9
7.0
4
5.2
6.5
8.0
5.4
4.5
5
3.2
4.5
6.0
3.4
2.5
6
1.7
3.0
4.5
1.9
1.0
Noise Figure
5 dB nominal
Isolation
> 90 dB
Power Requirements
12V 3A
The term “IC” before the radio certifi cation number only signifi es that Industry Canada technical specifi cations were met.
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be
adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter
incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster
is not in use for fi ve minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency
band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that
band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1
minute. After 5 (fi ve) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster
has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity
are maintained by the Signal Booster’s microprocessor.
The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple
carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-
radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or
gain reduction and not by an attenuator at the output of the device.
Specifi cations
