WilTec 61117 Operation Manual Download

Page: 6 / 14



Before using the tool on metal work pieces or work pieces containing metal make sure to remove

the dust bag.



Wear gloves when working with metal work pieces.



It is recommended that the tool always should be supplied by a residual current device with a rated

residual current of 30 mA or less.

Operation - Controls & Instructions

Components

A. On/ off switch

B. Lock-on button

C. Secondary handle

D. Straight arm

E. Belt tensioning lever

F. Belt tracking knob

G. Variable speed control knob

H. Dust bag

J. Cranked arm

Unpacking the Box

Carefully unpack all parts and check that all the parts listed below are included. If any items are miss-

ing, immediately contact the seller.

Equipment:



10 pc P80 sanding belts – 1 set



3 x sanding arms



Instruction manual – 1 piece

Artikel 61117

Seite 6

http://www.WilTec.de
http://www.aoyue.eu

09 2020

-1

http://www.teichtip.de

Summary of Contents for 61117















Search results

Summary of Contents for 61117

Reviews:

Related manuals for 61117

Brands by name

Popular brands

WilTec 61117, Operation Manual

Search results

Summary of Contents for 61117

Reviews:

Related manuals for 61117

Brands by name

Popular brands