background image

CONTROLS – NON TRACTION

 

 

SABER (SC)   86038350   01/29/07

 

3-6 

 

1. BRUSH 

SWITCH 

Controls the scrub brush motor. 

 
To turn scrub brush on, press the top of the 
switch.  
 
To turn scrub brush off, press the bottom of 
the switch. 
 

2.  BRUSH LIFT LEVER 

Raises and lowers the brush.  
 
To lower the brush, lift the lever from the 
notch, move to the left, then lower. 
 
To raise the brush, lift the lever from its 
lowered position.

 

 
 

3. VACUUM 

SWITCH 

Controls the vacuum motor. 
 
To start vacuum motor, press the top of the 
switch.  
 
To stop vacuum motor, press the bottom of 
the switch. 
 

4.  SQUEEGEE LIFT LEVER 

Raises and lowers the squeegee. 
 
To lower the squeegee, lift and pull the lever 
to the left and then lower. 
 
To raise the squeegee, lift the lever and push 
it to the right. 
 

5.  SOLUTION CONTROL LEVER 

Controls solution flow to scrub deck. 
 
To increase flow pull and raise the knob to the 
desired flow. 
 
To decrease flow push the knob down. 

 

6.  BATTERY CHARGE LEVEL INDICATOR 

Indicates the charge level of the batteries. 
 
The meter display is divided into 10 vertical 
bars.  Bars illuminated on the far right indicate 
full charge.  Bars flashing near the left side 
indicate the batteries should be recharged.  
Further operation of the machine could 
damage the machine or the batteries. 
 
When the machine is left overnight with less 
than a full charge, the display may initially 
indicate a full charge.  It will also indicate a full 
charge if the batteries are disconnected, then 
reconnected.  After a few minutes of operation 
the meter will give the correct charge level. 
 

7.  HOUR METER (OPTIONAL) 

Records the number of hours the machine’s 
brush has been in operation.  This information 
is useful in determining when to service the 
machine. 

 

8. CIRCUIT 

BREAKERS 

Circuit breakers interrupt the flow of power in 
he event of an electrical overload.  When a 
circuit breaker is tripped, reset it by pressing 
the exposed button.  If a circuit breaker 
continues to trip, the cause of the electrical 
overload should be found and corrected. 
 

30 Amp.  Protects the scrub brush 
motor. 
 
30 Amp.  Protects the vacuum 
motor.

 

 
 

 

Summary of Contents for Saber Compact 10052190






























Reviews: