MAINTENANCE
CUTTER 36V (SCEX) 86037040 12/12/06
2. SQUEEGEE BLADES
The front squeegee blade allows solution to pass
through channels in the blade into the squeegee
assembly while maintaining vacuum to provide lift.
The front blade has four wear surfaces and can be
rotated for extended life. The front blade should not
require regular replacement under normal use.
The rear blade wipes the floor to a near dry condition.
It is important the rear blade be in good condition to
properly do its job. As with the front, each squeegee
blade assembly has four wear surfaces for extended
service.
Check both the front and rear squeegee blades for
damage, wear, and adjustment each day in the pre-
run check. Change the front blade if it is torn or has
an uneven edge. Change the rear blade if it is less
than 1/2 the original thickness.
ADJUSTING SQUEEGEE
Adjusting the squeegee is a two-part process. First,
the squeegee assembly must have correct pitch in
order for the squeegee blade to have the same
deflection at each tip as well as the center. The knob
on the squeegee linkage controls the pitch
adjustment. The second adjustment is the deflection.
Knobs on each end of the squeegee control this.
4-6
TO REMOVE SQUEEGEE ASSEMBLY
1.
With the squeegee in the up position, turn key
switch “OFF”.
2.
Disconnect vacuum hose from squeegee and
loosen both knobs.
3.
Pull squeegee assembly rearward from the lifting
carrier.
4.
Inspect or repair as necessary and reinstall.
TO REPLACE OR ROTATE REAR
SQUEEGEE BLADES
1.
With the squeegee in the up position, turn key
switch “OFF”.
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.
2.
Remove the squeegee assembly from the
machine. Unlatch and remove blade retainer
strap and remove squeegee blade.
3.
Rotate the squeegee to new edge position or
replace as required. Each blade has four new
edge positions.
4.
Install blade on locating pins of squeegee
assembly.
5.
Install squeegee retainer strap.
6.
Fasten and lock latch, adjust latch only tight
enough to take up slack in retaining strap.
TO REPLACE OR ROTATE FRONT
SQUEEGEE BLADE
CORRECT
NOT ENOUGH
TOO MUCH
SQUEEGEE DEFLECTION
SIDE VIEW OF SQUEEGEE BLADE
1.
With the squeegee in the up position, turn key
switch “OFF”.
2.
Remove the squeegee from the machine.
Loosen three thumbscrews and remove the
retainer strap and squeegee blade.
3.
Rotate the squeegee to new edge position or
replace as required. Each blade has four new
edge positions. When installing the front blade,
tighten the center thumbscrew first. Insure that
the retainer strap is pressed against the blade
before tightening the outer screws.
Summary of Contents for Saber Cutter SCENX326
