THREADED ROD,
WASHER
AND NUT
FIGURE 8
7
INSIDE RV
Special instructions: For roof thickness greater
than 6-1/2”.
Parts Needed: (not included)
RP-4400 14” worm gear for roof
3200369 Directional handle extension
2162031 Long threaded rod
Instructions:
STEP 8.
Place nut on threaded rod.
See Figure 8.
STEP 9.
Measure and cut the threaded rod with a
hacksaw. Use the chart in Figure 9 to determine the
correct length.
STEP 10.
Remove the nut over the cut end of the
threaded rod. This cleans the threads after cutting.
STEP 11.
Thread the cut end of the rod into the hub.
STEP 12.
Install the ceiling plate. The rotate/lock lever
must point toward the rear of the vehicle.
Be sure rotate/lock lever is pointing towards the
rear of the vehicle and hole in ceiling plate aligns
with hole in the ceiling.
Refer to the chart to determine the correct length for
the directional handle. Extensions (3200369) may be
needed. Each extension adds 2-1/4” to directional
handle.
DO NOT cut the extension,
if the directional
handle must be extended by less than 2-1/4”, cut the
directional handle to fit.
NOTE: Be sure large and small keyways line up in
the hub and directional handle!
Roof Directional
Threaded Worm Gear
Thickness
Handle Length Rod Length
Shaft Length
(Figure 9)
(Figure 11)
1-1/2" ................. 2-7/8" ................... 2-3/4" ................... 2-7/8"
1-3/4" ................. 3-1/4" ................... 3" ......................... 3-1/8"
2" ........................ 3-1/2" ................... 3-1/4" ................... 3-1/2"
2-1/4" ................. 3-7/8 .................... 3-1/2" ................... 3-7/8"
2-1/2" ................. 4-1/8" ................... 3-3/4" ................... 4-1/8"
2-3/4" ................. 4-1/2" ................... 4" ......................... 4-1/2"
3" ........................ 4-3/4" ................... 4-1/4" ................... 4-3/4"
3-1/4" ................. 5" ......................... 4-5/8" ................... 4-7/8"
3-1/2" ................. 5-1/4" ................... 4-7/8" ................... 5-1/8"
3-3/4" ................. 5-5/8" ................... 5-1/4" ................... 5-1/2"
4" ........................ 5-3/4" ................... 5-1/2" ................... 5-3/4"
4-1/4" ................. 6-1/8" ................... 5-3/4" ................... 6-1/8"
4-1/2" ................. 6-1/2" ................... 6" ......................... 6-1/4"
4-3/4" ................. 6-5/8" ................... 6-1/8" ................... 6-3/8"
5" ........................ 6-7/8" ................... 6-3/8" ................... 6-5/8"
5-1/4" ................. 7-1/8" ................... 6-5/8" ................... 7"
5-1/2" ................. 7-3/8" ................... 6-7/8" ................... 7-1/4"
5-3/4" ................. 7-5/8" ................... 7-1/4" ................... 7-1/2"
6" ........................ 7-7/8" ................... 7-1/2" ................... 7-3/4"
6-1/4" ................. 8-1/8" ................... 7" ......................... 8"
6-1/2" ................. 8-1/2" ................... 7-3/4" ................... 8-1/4"
6 3/4" .................. 8 3/4" ................... 8" ......................... 8 1/2"
7" ........................ 9" ......................... 8 1/4" ................... 8 7/8"
7-1/4" ................. 9-3/8" ................... 8 5/8" ................... 9 1/8
7-1/2" ................. 9-5/8" ................... 8 7/8" ................... 9 3/8
7-3/4" ................. 9-7/8" ................... 9 1/8" ................... 9 5/8
8" ........................ 10-1/8" ................. 9 3/8" ................... 10
8-1/4" ................. 10-3/8" ................. 9 5/8" ................... 10 1/4
8-1/2" ................. 10-3/4" ................. 9 7/8" ................... 10 3/8
8-3/4" ................. 11" ....................... 10" ....................... 10 5/8
9" ........................ 11-1/4" .................. 10-1/4" ................. 11
9-1/4" ................. 11-1/2" .................. 10-5/8" ................. 11 1/4
9-1/2" ................. 11-3/4" .................. 10 7/8" ................. 11 1/2
9-3/4" ................. 12" ........................11 1/8" ................. 11 3/4
10" ...................... 12-3/8" .................. 11 3/8" ................. 12
10-1/4" ............... 12-5/8" .................. 11 5/8" ................. 12 1/4
10-1/2" ............... 12-7/8" .................. 11 7/8" ................. 12 1/2
FIGURE 9
Rev. 7/04
FIGURE 10
FIGURE 11
Summary of Contents for RM-4600
