Winegard RM-4610 Owner'S Manual Download

Page: 10 / 16

Rotation
Clamp

ASSEMBLED VIEW

POINT TO

BACK OF RV

POINTER
MUST POINT
TO RED
SCREW ON
ROTATION
CLAMP
WHEN IN
TRAVEL
POSITION

CAUTION: After INITIAL
INSTALLATION, the
antenna should ROTATE
APPROXIMATELY 360°
FROM TRAVEL POSITION.
The pointer on the
DIRECTIONAL HANDLE
should point towards the
RED SCREW on the
ROTATION CLAMP when
in TRAVEL POSITION.

Ceiling Plate

Directional
Handle Extension

Directional
Handle

ALIGN POINTER
WITH ANTENNA
TRAVEL POSITION

(4) #10 Phillips Flat
Head Screws

FIGURE 15

ELEVATING
CRANK

HANDLE

(When installed,
extends 2-1/4"
from ceiling).
Snap Handle
into base
when not in

use.

Tighten screw snugly

Threaded Tube

Elevating Shaft

Flat Washer

Nut for
threaded tube

CAUTION:
The antenna MUST BE IN THE
TRAVEL POSITION before
ALIGNING the Directional
Handle and Ceiling Plate.

Red Screw

Summary of Contents for RM-4610

















Search results

Summary of Contents for RM-4610

Reviews:

Related manuals for RM-4610

Brands by name

Popular brands

Winegard RM-4610, Owner'S Manual

Search results

Summary of Contents for RM-4610

Reviews:

Related manuals for RM-4610

Brands by name

Popular brands