background image

16

Printed in U.S.A.  Winegard Company • 3000 Kirkwood Street • Burlington, Iowa 52601  © Winegard Company, 2003, 2005   2451070   Rev. 12/21/05

  Rev. 12/21/05

WINEGARD MOBILE PRODUCTS LIMITED WARRANTY

(2 YEARS PARTS; 1 YEAR LABOR)

Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of
original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized
Winegard dealer to repair or replace defective products.  No warranty claim will be honored unless at the time the claim is made,
Customer presents proof of purchase to an authorized Winegard dealer (to locate the nearest authorized Winegard dealer, contact
Winegard Company, 3000 Kirkwood Street, Burlington, Iowa 52601, Telephone 319-754-0600 or visit www.winegard.com). Customer
must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product is under warranty. If the date
of purchase cannot be verified, the warranty period shall be considered to begin thirty (30) days after the date of manufacture.

If a defect in material or workmanship is discovered, Customer may take the product to an authorized Winegard dealer for service.
Customer must provide proof of purchase to verify the product is under warranty.  If the product is brought to an authorized Winegard
dealer for service prior to expiration of year one (1) of the warranty period and a defect in material or workmanship is verified by
Winegard Technical Services, Winegard Company will cover the Winegard dealer’s labor charges for warranty service. The Winegard
dealer must contact Winegard Technical Services in advance for pre-approval of the service.  Approval of the service is at the sole
discretion of Winegard Company.

Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at 3000 Kirkwood Street, Burlington, Iowa
52601, Telephone 319-754-0600). Customer must return the product along with a brief description of the problem and provide Winegard
Technical Services with Customer’s name, address, and phone number. Customer must also provide proof of purchase to verify the
product is under warranty. If the product is returned before the expiration of the warranty period, Winegard Company will (at its option)
either repair or replace the product.

This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions or fails from:  improper installation,
misuse, abuse, neglect, accident, tampering, modification of the product as originally manufactured by Winegard in any manner
whatsoever,  removing or defacing any serial number, usage not in accordance with product instructions or acts of nature such as
damage caused by wind, lightning, ice or corrosive environments such as salt spray and acid rain.

RETURN AUTHORIZATION POLICY

A Return Material Authorization (RMA) is required prior to returning any product to Winegard Company or Winegard Warranty Services
under this warranty policy. Please call our Technical Services Department at (800) 788-4417 or send an e-mail to 

warranty@winegard.com

to obtain the RMA number. Please furnish the date of purchase when requesting an RMA number.  Enclose the product in a prepaid
package and write the RMA number in large, clear letters on the outside of the package.  To avoid confusion or misunderstanding, a
shipment(s) without an RMA number(s) or an unauthorized return(s) will be refused and returned to Customer freight collect.

WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE BY ANY
OTHER PERSON.

ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR
PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY.

In states that do not allow limitations on implied warranties, or the exclusion of limitation of incidental or consequential damages, the
above limitations or exclusions do not apply.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.

This warranty gives Customer specific legal rights.  Customer may also have other rights that may vary from state to state.

Summary of Contents for RM-4610

















Reviews: