Winegard WB-2000 Installation & Operation Manual Download

Page: 6 / 39

. INTRODUCTION

. System Overview

The Winegard HD Satellite Interface System allows your Winegard Movin’ View and

RoadTrip satellite systems to receive additional KU-band satellites than available with a

stand-alone system. In addition to more available satellites, you will be able to enjoy

additional High Definition programming available through your satellite service provider.

The Winegard HD Satellite Interface System is designed for use with a either a

Winegard Movin’ View or RoadTrip satellite system (sold separately). It is compatible with

both stationary and in-motion satellite systems.

The Winegard HD Satellite Interface System is compatible with the following service

providers and satellites:

Service Provider

Available Satellites

Dish Network

119°W, 110°W, 129°W (Automatic and Manual Mode)

61.5°W, 148°W (Manual Mode only)

DirecTV

101°W, 110°W, 119°W (Automatic and Manual Mode)

72.5°W (Manual Mode only)

Bell ExpressVu

82°W, 91.5°W (Automatic and Manual Mode)

The Winegard HD Satellite Interface System is compatible with the following Winegard

Automatic Satellite Systems:

Product Line

Model #

Movin’ View

MV-3500, MV3500A, MV3535A, MV3500T, MV3535T,

WI3535T, MV-0500*

RoadTrip

RT1200S, RT1235S, RT1200T, RT1235T, RTS-12W,

RTS-12B, RTT-12W, RTT-12B

*MV-0500 must be upgraded to MV3500A electronics. Contact Winegard Customer Service for details.

. Parts Provided With HD System

1. HD Satellite Interface Box

2. Clone Box

3. 25’ modular data cable, for use with clone box

4. 30’ modular data/power cable bundle with Heyco Connector

5. 2’ mini coax cable

6. Power Supply

7. Hardware Bag

8. Installation/Operation Manual

.3 Additional Equipment and Materials Required for Operation

1. Television or Video Monitor, HD Television required for HD programming.

2. Satellite Receiver with authorized programming. An HD receiver is required to receive

High Definition programming. Contact your service provider for details.

3. Approved sealant for roof.

4. For DirecTV subscribers, the Winegard 110°W HD Converter is required

(model WB-1100)

In order to receive

DirecTV Satellelite 110°W

programming, the

Winegard 110°W HD

Converter is required, sold

separately

(model WB-1100)

Some satellites listed

are not available in all parts

of the country.

Summary of Contents for WB-2000








































Search results

Summary of Contents for WB-2000

Reviews:

Related manuals for WB-2000

Brands by name

Popular brands

Winegard WB-2000, Installation & Operation Manual

Search results

Summary of Contents for WB-2000

Reviews:

Related manuals for WB-2000

Brands by name

Popular brands