WinGD X72-B Operation Manual Download | Manualshive

Page: 46 / 526

background image

•

Turning Gear and Slow turning

Before you engage the turning gear, make sure that the starting air supply is shutoff and
the indicator cocks are open.

When turning gear is engage, make sure that the indicator lamp “Turning gear in” is change
to local. Make sure that turning gear is locked during the maintenance procedure.

When the engine is stop for more than 30 min, do the slow turning of the turning gear just
before the engine start in order to prevent free rotation of the engine.

•

IMO and NOX components number

Make sure that identification numbers are available to easily find the required drawings and
certificate.

The schematic diagrams shows where to find the markings on the individual component
types as below.

○

Fx fuel valve nozzle or TC diffuser etc.

○

Pictures that show the number.

○

Technical files descriptions.

2.2.2

Safety notes

•

Danger

This warning is used when an operation, procedure, or use may cause personal injury or
loss of life.

•

Warning

This warning is used when an operation, procedure, or use may cause a latently dangerous
state of personal injury or loss of life.

•

Caution

This warning is used when an operation, procedure, or use may cause damage to or
destruction of equipment and a injury.

•

Note

This warning is used when an operation, procedure, or use may cause damage to or
destruction of equipment.

2.2.3

General safety warnings and cautions

WARNING

Injury hazard: Engine parts can fall down and injury to personnel can occur. Make sure that
no personnel is standing below the crane and the area is clear.

WARNING

Injury hazard: Do not open the cocks suddenly because it can discharge hot fluids and
gases. Make sure to give a clear way for liquids, gases and flames to flow through it.

WARNING

Injury hazard: The disassembly of the engine parts can cause sudden release of springs
and injury to personnel can occur. Always use the correct personal protective equipment.

X72-B

AA00-0000-00AAA-012A-A

Operation Manual

Safety precautions and safety guidelines

Winterthur Gas & Diesel Ltd.

- 46 -

Issue 003 2021-12

«
...
44
45
46
47
48
...
»

Summary of Contents for X72-B















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X72-B

Brand: Admiral Pages: 9

Brand: Yanmar Pages: 38

Air Cooled TR-10D

Brand: Wisconsin Pages: 46

Brand: Beckhoff Pages: 31

Brand: Hatz Diesel Pages: 63

Brand: TCF Pages: 16

Brand: Motion Pages: 52

Brand: Motion Pages: 64

Brand: Ingersoll-Rand Pages: 42

Brand: CERTIFIED Pages: 17

2005 250 EXC-F SIX DAYS

Brand: KTM Pages: 151

Brand: Ford Pages: 71

Brand: GAPOSA Pages: 8

EM-PME375 Series

Brand: Danfoss Pages: 60

Brand: Zenoah Pages: 8

Brand: A.O. Smith Pages: 52

Brand: RIEJU Pages: 100

Brand: Femi Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands